Abstract:Highlights • Carbon nanomaterials were synthesized in situ using a facile alcohol flame. • Lower flame temperatures were achieved with increasing amounts of aqueous ammonia. • Soot particles had concentrically stacked carbon layers with a diameter of 45±5 nm. • Carbon nanotubes (CNTs) were grown via the root growth mechanism. • I G /I D ratios of CNOs (2.33) and CNTs (1.05) indicate good graphitic crystallization. This study aimed to investigate the in-situ synthesis of nanostructured carbon materials using alcohol flames generated by a Bunsen lamp burner and a catalytic Ni substrate, as opposed to the chemical vapor deposition method. Four different liquid fuels were utilized, including n-butanol, ethanol, n-butanol/aqueous ammonia, and ethanol/aqueous ammonia. The carbon growth, morphology, and structure caused by the parameters of sampling position, temperature distribution, and liquid fuel type were investigated using the diffusion flame produced by the atmospheric alcohol lamp burner. The results show that the additive aqueous ammonia affects not only the flame temperature but also the axial position of the highest temperature. When using n-butanol and portions of 10%, 20%, and 30% of aqueous ammonia mixed fuels, carbon nanotubes (CNTs), and carbon nano-onions (CNOs) are both observed; however, using ethanol and the portions of 10%, 20%, and 30% of aqueous ammonia mixed fuels, only CNTs are synthesized. Soot particles show concentrically stacked carbon layers with a diameter of around 45±5 nm. CNTs have no encapsulated Ni catalytic particles at the closed tip, showing the root growth mechanism and indicating differences from the top growth mechanism. In addition, graphene could be synthesized in pure n-butanol and n-butanol/ammonia flames, but not in pure ethanol and ethanol/ammonia flames. The I G /I D ratio values of the raw CNOs (2.33) and CNTs (1.05) are greater than 1, where I G /I D is the intensity ratio of Raman G -band and D -band peaks, indicating good crystallization of the graphite layer of these nanostructured carbon materials. Notably, flame synthesis via an alcohol Bunsen lamp burner simplifies operations saves resources, and improves conventional production, demonstrating a facile and efficient method.

Carbon Nanotube Synthesis from Alcohol Using Catalytic Pyrolysis Method

Synthesis of Carbon Nanotubes by Decomposing Alcohol

Carbon Nanotubes Synthesized By Rapid Quenching Of Red-Hot Graphite Rod In Ethyl Alcohol

Growth Of High-Quality Single-Wall Carbon Nanotubes Without Amorphous Carbon Formation

Preparation of Well-Aligned Carbon Nanotubes by Pyrolysis of Phenolic Resin in Anodic Alumina Pores

Preparation and Growth Mechanism of Carbon Nanotubes Via Catalytic Pyrolysis of Phenol Resin

Synthesis Isolated Short Carbon Nanotubes by Simple One-Step Catalytic Pyrolysis Process

Controlled Growth of Single-Walled Carbon Nanotubes at Atmospheric Pressure by Catalytic Decomposition of Ethanol and an Efficient Purification Method

In situ flame-synthesis of nanostructured carbon materials via facile alcohol Bunsen burner

Controllable Synthesis of Carbon Nanotubes with Ultrafine Inner Diameters in Ethanol Flame

In situ transmission electron microscopy of temperature-dependent carbon nanofiber and carbon nanotube growth from ethanol vapor

Controllable and Large-Scale Synthesis of Metal-Free Carbon Nanofibers and Carbon Nanocoils over Water-Soluble Naxky, Catalysts

Carbon nanotube prepared by catalytic pyrolysis of methane

Large-Scale and Controllable Synthesis of Metal-Free Carbon Nanofibers and Carbon Nanotubes over Water-Soluble Na2co3

Controlled synthesis of carbon nanocables and branched-nanobelts

Controlled Synthesize Isolated Bamboo-like Carbon Nanotubes

Fabrication, Characterization, Purification and Photoluminescence Properties of Carbon Nanomaterials over Water-Soluble Alkali Salts

Synthetic Hierarchical Nanostructures: Growth of Carbon Nanofibers on Microfibers by Chemical Vapor Deposition

Fabrication of High Quality Carbon Nanotubes with a Simple Ethanol-Assisted Arc Discharge Process.

Fabrication and Characterization of Single-Walled Carbon Nanotubes from La2O3 Nanoparticles by Ethanol Chemical Vapour Deposition

Synthesis Of High Quality Single-Walled Carbon Nanotubes By Cvd And Effect Of Catalyst'S Acidity-Basicity On Nanotubes Growth