Abstract:The reactive extrusion of maleic anhydride grafted polypropylene (PP-g-MAH) with ethylenediamine (EDA) as coupling agent was carried out in a co-rotating twin-screw extruder to produce long chain branched polypropylene (LCBPP). Part of PP-g-MAH was replaced by maleic anhydride grafted high-density polyethylene (HDPE-g-MAH) or linear low-density polyethylene (LLDPE-g-MAH) to obtain hybrid long chain branched (LCB) polymers. Compared with the linear PP, PE and their blends, the LCB polyolefins exhibit excellent dynamic shear and transient extensional rheological characteristics such as increased dynamic modulus, higher low-frequency complex viscosity, significantly enhanced melt strength and strain-hardening behaviors. LCB polymers also have higher tensile strength, tensile modulus, impact strength and lower elongation at break than linear polymer and their blends. Supercritical carbon dioxide (scCO2) was introduced in the reactive extrusion process. With the presence of scCO 2, the motor current of twin extruder was decreased and LCB polyolefins with lower MFR, higher complex viscosity and increased tensile strength and modulus were obtained. This indicates that the application of scCO2 can reduce the viscosity of melt in extruder, enhance the diffusion of reactive species, facilitate the reaction between functional groups, and increase the LCB density. The foaming behavior of both linear and LCB polyolefins were studied. The results show that cellular materials produced from the LCB polyolefins have higher weight reduction, smaller cell size and better mechanical properties than those produced from the linear polymers.

Preparation and Properties of Metallocene POE/PP TPV

Preparation Of Comb-Shaped Polyolefin Elastomers Having Ethylene/1-Octene Copolymer Backbone And Long Chain Polyethylene Branches Via A Tandem Metallocene Catalyst System

Preparation of Polypropylene/MMT Nanocomposites Using Complex Supported Catalysts

Effect of Extrusion Process on Properties of POE/PP TPV

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Synergistic Effect of Sbs and Trimethylopropane Trimethacrylate (tmptma) on Dynamically Vulcanized Sebs/Pp Blends

Study on compatibilization of EPDM/PP TPV

Foamed ethylene-propylene-diene rubber/polypropylene thermoplastic vulcanizate prepared by chemical foaming Ⅰ. Extrusion processing parameters

Study on EPDM/PP TPV

Study on the Preparation and Properties of POE/PP Dynamic Vulcanized Thermoplastic Elastomers with Low Degree of Hardness

Preparation, Curing Properties, and Phase Morphology of Epoxy-Novolac Resin/multiepoxy-Terminated Low-Molecular-weight Poly(phenylene Oxide) Blend

Morphological structure of dynamically vulcanized thermoplastic elastomer of ethylene propylene diene monomer/polypropylene

Preparation of TPEE/ACM/Nano-SiO_2 Composite via Dynamic Vulcanization

Preparation and Characterization of High Melt Strength Thermoplastic Polyester Elastomer with Different Topological Structure Using a Two-Step Functional Group Reaction

Effect of crosslinking agent dosage on the morphology and properties of thermoplastic vulcanizates based on hydrogenated acrylonitrile butadiene rubber and thermoplastic polyester elastomer

Preparation and Properties of Ethylene Octane Copolymer Blends with High Strength and Polarity

Effect of Additives on the Morphology Evolution of EPDM/PP TPVs During Dynamic Vulcanization in a Twin-Screw Extruder

Ethylene propylene diene monomer/polypropylene thermoplastic elastomer modified with in situ prepared zinc dimethacrylate

A method to essentially increase the compatibility of thermoplastic polyurethane/methyl vinyl silicone rubber based thermoplastic vulcanizate

Effect of Morphology Development on the Low‐temperature Tensile Properties of PP / POE Blends