Abstract:The present study investigates the variations in the microstructure and mechanical properties of AA2024 aluminum alloy as a consequence of thermal and strain gradient in combined hot forming cold die quenching (HFQ) and equal channel angular pressing (ECAP) method. Solution-treated AA2024 aluminum alloy was HFQ–ECAPed for five passes of deformation and 3D simulations plus microstructural evolutions, and mechanical properties over the thickness of the sample were investigated. Furthermore, after each ECAP pass, intermediate solution treatment was applied, and a group of specimens was subjected to aging treatment following the deformation. 3D simulations illustrated strain uniformity by increasing the number of deformation passes with its maximum uniformity after four passes. Microstructural observations demonstrated evident grain refinement in successive passes, which were higher in the central and top parts of the sample than in the lower area. Also, a high quantity of shear bands occurred in the workpiece after the first ECAP pass. However, shear banding was deducted in the consecutive passes of deformation and intermediate solutionizing. Preferable properties in central regions were seen comparing tensile properties in surface area and central parts. Besides, the microhardness test resulted in more uniform outcomes by enhancement in the number of ECAP passes. Hardness variations showed an increase in average hardness after the first pass of deformation (compared to the annealed condition (Baghbani Barenji et al. in J Mater Res Technol 9:1683–1697, 2020) and then a negligible decrease in the following two passes. The hardness quantities again increased in the fourth pass and then dramatically decreased after the fifth pass due to the partial decomposition of the solid solution. Besides, due to strain distribution, hardness values illustrate the maximum and minimum amount in the uppermost and lowermost areas, respectively. The overall conclusions of this article presented mechanical similarities in the surface and inner parts of the material.

A finite element study of the temperature rise during equal channel angular pressing

Tensile and Compressive Deformation Behaviors of Commercially Pure Al Processed by Equal-Channel Angular Pressing with Different Dies

Finite Element Simulation and Analysis of Aluminum Alloy Three-Dimensional Milling

Simulation of High-Speed Milling Process of Aerospace Aluminum Alloy

Study on the Effect of Tool Inclination Angle in Machining Process Based on Three-Dimensional Thermo-Elastic-Plastic Model

Research on 3D Numerical Simulation and Experiment of Cutting Temperature for High Speed Milling of Aerospace Aluminum Alloy

Heat Analysis of Sliding Abrasive Particle Micro Contact Process by Finite Element Method

Mechanical and microstructural characteristics of AA6082 using thermal equal channel angular pressing for structural applications

Temperature Simulation of Aluminium Alloy Double-Arc Welding Process on Simplified Conditions

Finite Element Simulation and Experimental Investigation of Hot Forming Cold Die Quenching and Equal Channel Angular Pressing of AA2024 Aluminum Alloy

The microstructure and mechanical properties of Mg-Sn-based alloy processed by differential-thermal equal channel angular pressing

Impact of Equal Channel Angular Pressing on Mechanical Behavior and Corrosion Resistance of Hot-Rolled Ti-2Fe-0.1B Alloy

Influence of equal channel angular pressing in an acute angle die with a back pressure notch on grain refinement, torsion and mechanical properties of aluminium

Study on equal channel angular pressing process of Mg–Zn–Y–Mn–Ti magnesium alloy enhanced by lamellar LPSO phase and spherical W phase

Effect of the Equal Channel Angular Pressing on the Microstructure and Phase Composition of a 7xxx Series Al-Zn-Mg-Zr Alloy

New Formulas of Shear Strain During Equal-channel Angular Pressing Process with Consideration of Influences of Velocity and Motion Trajectory

Ebsp Investigation of Microstructure and Texture Evolution During Equal Channel Angular Pressing of Aluminium

Tensile Deformation Behaviors of CuNi Alloy Processed by Equal Channel Angular Pressing

Electron Backscatter Diffraction Investigation on Microstructure Evolution of TiB2(p)/Al-Cu Composite after Single-Pass Equal Channel Angular Pressing for Formability Assessment

Deformation mechanism finite element analysis and die geometry optimization of magnesium alloys by equal channel angular processing

Reducing the Tension–compression Yield Asymmetry of Extruded Mg–Zn–Ca Alloy Via Equal Channel Angular Pressing