Abstract:CeO2-based materials are widely applied in a three-way catalyst framework for catalytic combustion of diesel soot. For the application of CeO2 in coking inhibition during thermal cracking of hydrocarbons, SiO2–CeO2 and SiO2 coatings were prepared on HP40 alloy samples through sol–gel dip coating. The coatings were then characterized in terms of morphology and microstructure perspectives, and their anticoking performances were evaluated under conditions relevant to the practical applications during thermal cracking of naphtha. Results showed that the addition of ceria could improve the quality of the silica coating, which subsequently presented better anticoking properties by preventing formation of catalytic coking. Furthermore, thermogravimetric analysis (TGA) results of coke samples revealed that the ceria in the coating had the potential function as a coke oxidation catalyst. However, the silica–ceria coating lost its coking resistance after approximately ten repetitious coking/decoking cycles. Nevertheless, the combined application of anticoking coatings and addition of dimethyl disulfide (DMDS) into the naphtha feed could mitigate risks of coke formation more effectively compared with pure coatings only because of its preferential adsorption of sulfur-based radicals at the coating defects. In particular, the application of the SiO2–CeO2 coating combined with the addition of DMDS could still maintain a stable anticoking rate of above 60% throughout three cycles of coking/decoking operations.This article has not yet been cited by other publications.

Study of Anti-Coking Property of SiO2/S Composite Coatings Deposited by Atmospheric Pressure Chemical Vapor Deposition

Preparation and Anti-coking Property of SiO 2 /S Coating on HP40 Tube

Deposition and Microstructures of SiO2/S Anti-Coking Coatings

Microstructure and oxidation behavior of SiOC coatings on C/C composites co-deposited with HMDS and TEOS by using CVD process

Effect of substrate pre-oxidation on SiO2/S composite coating deposited on HP40 alloy

Kinetic study of SiO2/S coating deposition by APCVD

A study on acceleration and inhibition of coking on metal surfaces by micropyrolysis of ethylene feedstocks

Preparation of TiO2/SiO2 Composite by Chemical Coating Method

Mechanical and Thermal Properties of SiO2/S Composite Coating Prepared by APCVD

Anti-coking Performance of Cr/CeO2 Coating Prepared by High Velocity Oxygen Fuel Spraying

Investigation into the Anticoking Performances of Sol–Gel-Derived SiO 2 and SiO 2 –CeO 2 Coatings during Thermal Pyrolysis of Light Naphtha

Silicon oxide anticorrosion coating deposition on alloy steel surface by low temperature plasma

The Power Source Effect on SiOx Coating Deposition by Plasma Enhanced Chemical Vapor Deposition

Preparation and anti-coking performance of TiO2 coatings deposited by metal organic chemical vapor deposition method

Fabrication Of Silica And Titania Anti-Coking Passivation Layers In High Aspect-Ratio Tubular Reactors By Atomic Layer Deposition

Influence of the SiO 2/S coating and sulfur/phosphorus-containing coking inhibitor on coke formation during thermal cracking of light naphtha

Preparation and Corrosion Properties of TiO2-SiO2-Al2O3 Composite Coating on Q235 Carbon Steel

Preparation and anti-coking application of sol–gel SiO 2 coating in a delayed coking furnace

Compaction of Hydrophobic Molybdenum Disulfide Coatings for Promoting Tribological Behaviors on Engineering Steel

Atomic Layer Deposition of TiO2 Thin Films on the Inner Walls of Steel Tubes Increases Anti-coking Properties.

STUDY OF MICRO-OXIDATION PROPERTIES AND MECHANISM OF SIO2 COATING / 3-D CARBON FIBER BRAID THROUGH MULTI-HEATING RATES