Abstract:Composite NOx sensors were fabricated by combining partially and fully stabilized yttria-doped zirconia with alumina forming a composite electrolyte, Y2O3-ZrO2-Al2O3, and strontium-doped lanthanum manganese oxide mixed with gold to form the composite sensing electrode, La0.8 Sr0.2MnO3-Au. A surface chemistry analysis of the composite sensor was conducted to interpret defects and the structural phases present at the Y2O3-ZrO2-Al2O3 electrolyte, as well as the charge conduction mechanism at the LaSrMnO3-Au electrode surface. Based on the surface chemistry analysis, ionic and electronic transport properties, and microstructural features of sensor components, the working principle was described for NOx sensing at the composite sensor. The role of the composite materials on the NOx sensing response, cross-sensitivity to O2, H2O, CO, CO2, and CH4, and the response/recovery rates relative to sensor accuracy were characterized by operating the composite NOx sensors via the impedimetric method. The composite sensors were operated at temperatures ranging from 575 to 675 °C in dry and humidified gas environments with NO and NO2 concentrations varying from 0 to 100 ppm, where the balance gas was N2. It was found that the microstructure of the composite NOx sensor electrolyte and sensing electrode had a significant effect on interfacial reactions at the triple phase boundary, as well as the density of active sites for oxygen reactions. Overall, the composite NOx sensor microstructure enabled a high NOx sensing response, along with low cross-sensitivity to O2, CO, CO2, and CH4, and promoted NO detection down to 2 ppm.

A Fully Solid-State SOx (x = 2,3) Gas Sensor Utilizing Ag-ß″-alumina As Solid Electrolyte

THE PERFORMANCE EVALUATION OF A FULLY SOLID STATE SOx(x=2,3)GAS SENSOR

Electrochemical Sox (X=2 Or 3) Gas Sensor Based On Solid Electrolytes

Increasing the Sensitivity of an Amperometric, YSZ-based Total-Nox Sensor by Opening the Gas Diffusion Pathways in a Porous La0.8Sr0.2MnO3 Electrode

Au thin-film electrodes based potentiometric CO2 sensor using Li3PO4 as both the reference material and the solid electrolyte

Electrochemical Sensor for Dissolved Carbon Dioxide Measurement

Response Characteristics of A Potentiometric Co2 Gas Sensor Based on Li3po4 Solid Electrolyte Using Au Film As the Electrodes

New All-Solid-state Carbonate Ion-Selective Electrode with Ag 2 CO 3 -Baco 3 As Sensitive Films

Solid-Electrolyte Amperometric Sensor for Simultaneous Measurement of CO and CO2 in Nitrogen

Room temperature solid electrolyte ozone sensor based on Ag-doped SnO 2

Investigation of an Impedimetric LaSrMnO3-Au/Y2O3-ZrO2-Al2O3 Composite NOx Sensor

An application of the electrochemical sulfur sensor in steelmaking

Preparation of H-2 and Lpg Gas Sensor

Potentiometric NO2 Sensors Based on Thin Stabilized Zirconia Electrolytes and Asymmetric (La0.8Sr0.2)0.95MnO3 Electrodes

An Amperometric Type NO2 Sensor Utilizing La0.7Sr0.3MnO3-δ-NiO Composite Sensing Electrode

Fumed SiO2-H2SO4-PVA Gel Electrolyte CO Electrochemical Gas Sensor

A YSZ-based mixed potential sensor achieving fast detection and complete recovery to SO 2 through combining a high-temperature pulse and Pd catalyst in sensing electrode

A Fuel-Cell-Type Sensor for Detection of Carbon Monoxide in Reformed Gases

An Ultrasensitive Biosensor for Superoxide Anion Based on Hollow Porous PtAg Nanospheres.

In Situ Ba2+ Exchange in Amorphous TiO2 Hollow Sphere for Derived Photoelectrochemical Sensing of Sulfur Dioxide

YSZ-Based Mixed Potential Type Sensors Utilizing Pd-doped SrFeO 3 Perovskite Sensing Electrode to Monitor Sulfur Dioxide Emission