Abstract:1.4 %C ultra high carbon steel (UHCS) was prepared in order to study the structure of martensite transformation and mechanical properties. Ultra-fine spherical carbide and ultra-fine austenite grain size were obtained. A great deal of lath martensite was observed after quenching. The phenomenon does not agree with the traditional knowledge that the lath martensite would disappear when carbon content is in excess of 0.8% in austenite. The strength, fatigue properties and fracture toughness have been measured. A good combination of strength, toughness and fatigue properties come from fine and uniform distributed carbide particles and ultra-fine austenite grain size. Fracture strength increases by 48%, yield strength increases by 15% and plasticity keep the same comparing with that of hardened and tempered 40CrNiMo. The carbon content of ultrahigh carbon steels (UHCS) is in the range of 1.0-2.1% [1, 2]. Traditional heat treatments for normal steels will cause the microstructure of UHCS to be coarse and do not produce optimal properties. With controlled rolling and special heat treatment, UHCS can be in ferrite, pearlite, bainnite or martensite structures, which all have different mechanical properties. The yield stress of a 1.8%C, 1.6%Al ferrite UHCS can reach 1500MPa, which is much higher than that of high strength and plain alloy steels [3]. The tensile strength of a 1.25%C-1.5%Cr pearlite UHCS can reach 1810Mpa and its elongation can be 18%. When it is treated into martensite, its compression strength reached to 4690Mpa and compression strain reached to 26% [1, 4], which is comparable to WC-12Co. Such good mechanical properties can be ascribed to the ultra fine grain sizes because of the undissolved carbide particles which resist growth of austenite grain during heating. Another reason could be the lath martensite structures. O.D.Sherby [4] had reported that there was a lot of lath martensite in quenched UHCS. The UHCS was considered not only as tool steels but also as good structure materials. Fracture and fatigue properties are important for structure materials. However, they have rarely been studied. The present paper is going to study the martensite structure and mechanical properties of a prepared 1.4% C UHCS.

Mechanical Prperties and Microstructure of Heat-Treated Ultrahigh Carbon Steels

Microstructure and Mechanical Properties of A 1.4%C Ultra High Carbon Steel

Mechanical Properties of Plain Carbon Steels with Ultrafine (α+θ) Microstructures

Effect of Heat Treatment on Mechanical Properties and Microstructure of Advanced High-Strength Steel

Microstructure Evolution of Ferrite and Martensite Phases during Heat Treatment of the Ultralow‐Carbon 11.3Cr–1.7Mn–0.8Ni Steel

Effect of Rapid Heating and Quenching on Microstructure and Mechanical Properties of High Strength Low Alloy Steel

Microstructure and Properties of 1.6%C Ultra-high Carbon Steel

Effect of Multistage Heat Treatment on Microstructure and Mechanical Properties of High-Strength Low-Alloy Steel

Study on the Microstructures and Fatigue Properties of 1.4 ％C Ultra-High Carbon Steel

Effect of Heat Treatment on Microstructure and Properties of Improved 40crni2si2mov Steel

Effect of heat treatment on microstructure and mechanical properties of S31042 austenite heat resistant steel

The Microstructure and Mechanical Properties of Ferritic-Martensitic Steel EP-823 after High-Temperature Thermomechanical Treatment

Achieving Fine-Grained Microstructure and Superior Mechanical Property in a Plain Low-Carbon Steel Using Heavy Cold Rolling Combined with Short-Time Heat Treatment

Effect of carbon content and microstructural refinement on the mechanical property of quenching-partitioning - tempering-treated steels

The sensitivity of the microstructure and properties to the peak temperature in an ultrafast heat treated low carbon-steel

Effect of Heat Treatment on Microstructure and Properties of Powder Metallurgy High-Speed Steel Prepared by Hot Isostatic Pressing

Microstructures and Mechanical Properties of a Newly Developed Austenitic Heat Resistant Steel

Effect of Austenitising Temperature on Microstructure and Mechanical Properties of 30si2crni4monb Ultrahigh Strength Steel

Microstructure and properties of ultrafine grained ultrahigh carbon (1.73 Pct C) steel

Study on Preparation and Heat Treatment Process of Ultrahigh Carbon Steel

Microstructure Regulation and Mechanical Properties of Low-Carbon Multiphase Steels