Abstract:Globally, most oil fields use excessive water flooding to recover oil. By injection of water between wells, channels are created, which result in lower oil recovery. Water-plugging deep-profile control must be used to control the excessive water production from an oil reservoir. This laboratory study used sulfonated polyacrylamides with a molecular weight of 10.3-13.0 × 10<sup>6</sup> Da (FPAM) and polyethylenimine (PEI-600) to formulate a weak gel system to control excessive water production from deep formations. Using different FPAM and PEI-600 concentrations, the Sydansk bottle test approach was applied to evaluate the gelation time, strength, and stability of the weak gel. The weak gel concentration of 0.5 wt % FPAM and 0.4 wt % PEI-600 was confirmed for deep-profile control by this approach. The temperature and salt resistance of the selected weak gel system were evaluated using the same bottle test methodology. The gelation time depends on temperature: 5-7 days at <100 °C to 0.5 days >100 °C. Salinity >20,000 mg/L significantly affected the weak gel system's strength. By performing a viscometer test, the viscosity of the weak gel system at different times was evaluated, confirming the gelation time of the selected weak gel. Next, a microfluidic chip flooding test analyzed weak gel performance and plugging ability in porous media. This micromodel provided a visual analysis of the weak gel plug. Finally, a low- to medium-permeability sandstone core-flooding was conducted to determine the plugging rate of weak gel at the core scale, followed by an evaluation of the injection pressure, blocking effect, and oil recovery. According to the study, the selected weak gel has an extended gelation time with a significantly low viscosity, which affects its injectivity and can move from injection wells into deep formations. In the core-flooding test, the weak gel's blocking rate after 7 days of gelation time exceeded 90%.

Laboratory Study on the High Strength Gel System

Preparation Method and Performance Evaluation of a Gel Based on AM/AMPS Copolymer

Preparation and Performance Evaluation of Temperature-Resistant and Salt-Resistant Gels

Formulation Development of High Strength Gel System and Evaluation on Profile Control Performance for High Salinity and Low Permeability Fractured Reservoir

Experimental Study of Oilfield Water Plugging with Organic Chromium Gel

Preparation and Characterization of Temperature-Sensitive Gel Plugging Agent

Optimization of the Methods to Develop Stable Polymer Gels for Water Management in Medium- and Ultra-High-Salinity Reservoirs

Synthesis and Performance Evaluation of a Novel Heat and Salt-Resistant Gel Plugging Agent

Development and evaluation of organic/inorganic combined gel for conformance control in high temperature and high salinity reservoirs

Preparation of high-temperature gels for enhanced oil recovery using methyl etherized melamine-formaldehyde resin

Application of a Salt-Resistant In Situ Cross-Linked Terpolymer Gel for the Daqing Oilfield

Development of a High-Strength and Adhesive Polyacrylamide Gel for Well Plugging

A novel profile modification HPF-Co gel satisfied with fractured low permeability reservoirs in high temperature and high salinity

Experimental Performance Evaluation and Optimization of a Weak Gel Deep-Profile Control System for Sandstone Reservoirs

The study of an inorganic gel for profile modification in high-temperature and low-permeability sandstone reservoirs

Investigation of In Situ Gelation Behavior and Enhanced Oil Recovery Ability of Polymer Gel Used for Controlling CO2 Channeling in Tight Fractured Reservoir

Novel Gel with Controllable Strength for In-Depth Conformance Control: Bulk Gelation Performance and Propagation Properties in Porous Media

Plugging Mechanisms Of Polymer Gel Used For Hydraulic Fracture Water Shutoff

Development of dual-crosslinked nanocomposite gel for water management in high-temperature reservoirs

Effect of AMPS(2-acrylamido-2-methylpropane sulfonic acid) content on the properties of polymer gels

Preparation and Experimental Study of a Low-Initial-Viscosity Gel Plugging Agent