Abstract:Abstract Water injection increases the percentage of recovery by means of providing pressure support and displacing the oil in the heterogeneous porous medium. In such a displacement process, mobility ratio is important for a more efficient displacement of oil by the injected fluid where mobility ratio can be improved using the fluids involving gelling agents, resulting in increased volumetric sweep. While polymers degrade and break up upon experiencing sudden extreme shear stresses and temperatures, polymer macromolecules are forced to flow into narrow channels and pores, molecular scission processes can take place, thus it is of outmost importance to have a strong understanding of use of right type and amount of viscosity reduction agent. For polymer injection, a comparison of xanthan polymer and synthetic polymer mechanisms was conducted. A commercial full-physics reservoir simulator is coupled with a robust optimization and uncertainty tool to run the model where a simplified gel kinetics is assumed to form a microgel with no redox catalyst. Water injection continues over all 6 layers for 450 days, followed by gel system injection for 150 days, in the bottom 2 layers. Water injection is continued to 4 years. The top four layers have higher horizontal permeabilities, and a high-permeability streak is at the bottom of the reservoir to reduce any helpful effects of gravity. Control and uncertainty variables are set to investigate the sensitivity under this process using the coupled optimization and uncertainty tool. Results demonstrate deep penetration of gel and blocking of the high permeability bottom layers. Sensitivity studies indicate the relative merits of biopolymer, xanthan polymer in terms of viscosity effects vs synthetic PAM in terms of resistance factor vs insitu gelation treatments and their crossflow dependence. Adsorption and retention of polymer and gel are permeability dependent. Considering the fact that there is a significant potential for application of gel solutions in the US and throughout the world, this study illustrates the relative advantages of different treatments in terms of viscosity reduction in the same model in a comparative way outlining the significance of each control and uncertainty variable for better management of reservoirs where displacement efficiency is very critical.

Experimental Study of Oilfield Water Plugging with Organic Chromium Gel

Production Optimization under Injection of Biopolymer, Synthetic Polymer and Gels in a Heterogeneous Reservoir

Preparation and Experimental Study of a Low-Initial-Viscosity Gel Plugging Agent

Preparation Method and Performance Evaluation of a Gel Based on AM/AMPS Copolymer

Starch graft copolymer and polymer gel applied in Bohai oilfield for water plugging and profile control and their mechanisms

APPLICATION PROGRESS OF INSITU POLYMER GEL IN OILFIELD CONFORMANCE CONTROL TREATMENT

Development and Application of the Anti-High-Temperature Delayed Crosslinking Polymer as a Gel Plugging Additive for Drilling Fluid

Preparation and Performance Evaluation of a Supramolecular Polymer Gel-Based Temporary Plugging Agent for Heavy Oil Reservoir

Preparation and Characterization of Temperature-Sensitive Gel Plugging Agent

Lignocellulosic hydrogel for profile control and water plugging in high salt reservoirs

Development and Application of Polymer Plugging Remover for Polymer Injection Well in Changqing Oilfield

Nanocellulose/scleroglucan-enhanced robust, heat-resistant composite hydrogels for oilfield water plugging

Evaluation of Supramolecular Gel Properties and Its Application in Drilling Fluid Plugging

Water Management and Oil Recovery Improvement Performance of High-Strength Preformed Particle Gels in Fractured Conglomerate Reservoirs

Synthesis and Performance Evaluation of an Organic/Inorganic Composite Gel Plugging System for Offshore Oilfields

A novel polymer gel with high-temperature and high-salinity resistance for conformance control in carbonate reservoirs

Study on Water plugging Technology of Self - Generating Gel-Foam in Offshore Oilfield

Development and Performance Evaluation of a New Conformance Control Agent Gel

Design, synthesis, and characterization of novel copolymer gel particles for water-plugging applications

Development of in-situ starch grafted copolymerized gels for conglomerate reservoir conformance control and oil recovery improvement

A novel profile modification HPF-Co gel satisfied with fractured low permeability reservoirs in high temperature and high salinity