Abstract:Abstract Water injection increases the percentage of recovery by means of providing pressure support and displacing the oil in the heterogeneous porous medium. In such a displacement process, mobility ratio is important for a more efficient displacement of oil by the injected fluid where mobility ratio can be improved using the fluids involving gelling agents, resulting in increased volumetric sweep. While polymers degrade and break up upon experiencing sudden extreme shear stresses and temperatures, polymer macromolecules are forced to flow into narrow channels and pores, molecular scission processes can take place, thus it is of outmost importance to have a strong understanding of use of right type and amount of viscosity reduction agent. For polymer injection, a comparison of xanthan polymer and synthetic polymer mechanisms was conducted. A commercial full-physics reservoir simulator is coupled with a robust optimization and uncertainty tool to run the model where a simplified gel kinetics is assumed to form a microgel with no redox catalyst. Water injection continues over all 6 layers for 450 days, followed by gel system injection for 150 days, in the bottom 2 layers. Water injection is continued to 4 years. The top four layers have higher horizontal permeabilities, and a high-permeability streak is at the bottom of the reservoir to reduce any helpful effects of gravity. Control and uncertainty variables are set to investigate the sensitivity under this process using the coupled optimization and uncertainty tool. Results demonstrate deep penetration of gel and blocking of the high permeability bottom layers. Sensitivity studies indicate the relative merits of biopolymer, xanthan polymer in terms of viscosity effects vs synthetic PAM in terms of resistance factor vs insitu gelation treatments and their crossflow dependence. Adsorption and retention of polymer and gel are permeability dependent. Considering the fact that there is a significant potential for application of gel solutions in the US and throughout the world, this study illustrates the relative advantages of different treatments in terms of viscosity reduction in the same model in a comparative way outlining the significance of each control and uncertainty variable for better management of reservoirs where displacement efficiency is very critical.

Novel Gel with Controllable Strength for In-Depth Conformance Control: Bulk Gelation Performance and Propagation Properties in Porous Media

Production Optimization under Injection of Biopolymer, Synthetic Polymer and Gels in a Heterogeneous Reservoir

Development and evaluation of organic/inorganic combined gel for conformance control in high temperature and high salinity reservoirs

A Novel Branched Polymer Gel System with Delayed Gelation Property for Conformance Control

Development and Performance Evaluation of a New Conformance Control Agent Gel

Investigation of In Situ Gelation Behavior and Enhanced Oil Recovery Ability of Polymer Gel Used for Controlling CO2 Channeling in Tight Fractured Reservoir

APPLICATION PROGRESS OF INSITU POLYMER GEL IN OILFIELD CONFORMANCE CONTROL TREATMENT

Field design guidelines for gel strengths of profile-control gel treatments based on reservoir type

Gelling Behavior of PAM/Phenolic Crosslinked Gel and Its Profile Control in a Low-Temperature and High-Salinity Reservoir

Experimental Performance Evaluation and Optimization of a Weak Gel Deep-Profile Control System for Sandstone Reservoirs

Experimental investigation for the dynamic adsorption behaviors of gel system with long slim sandpack: Implications for enhancing oil recovery

Preparation Method and Performance Evaluation of a Gel Based on AM/AMPS Copolymer

Experimental Evaluation of Performance of a Low-Initial-Viscosity Gel Flooding System

A novel polymer gel with high-temperature and high-salinity resistance for conformance control in carbonate reservoirs

Property Study on Novel Waterflood Conformance Control Gels

Formulation Development of High Strength Gel System and Evaluation on Profile Control Performance for High Salinity and Low Permeability Fractured Reservoir

The Effect of Shear Rate on Dynamic Gelation of Phenol Formaldehyde Resin Gel in Porous Media

A novel profile modification HPF-Co gel satisfied with fractured low permeability reservoirs in high temperature and high salinity

Development of dual-crosslinked nanocomposite gel for water management in high-temperature reservoirs

Fabrication and Properties of in Situ Cross‐Linked Supramolecular Gel Based on Host‐Guest Interaction

Optimization of the Methods to Develop Stable Polymer Gels for Water Management in Medium- and Ultra-High-Salinity Reservoirs