Abstract:Based on electron backscatter diffraction (EBSD), hollow structures of Ni foam struts fabricated by electroplating on a chemically removable template were observed. Three-dimensional (3D) pore structures of Ni foams were also obtained using X-ray computed tomography (CT), and microstructural features such as porosity, pore size and strut thickness were statistically quantified. Evolution of microstructure and mechanical properties during ex situ compression of open-cell Ni-foams was investigated based on X-ray CT, and experimental results were compared with predictions by the finite element method (FEM). 3D microstructures obtained by X-ray CT revealed that the stress drop started with the buckling of struts at the center of the Ni-foams. The flow stress increased after the buckling of the struts spreads to most of the regions. For effective simulation of the compressive deformation and determination of the microstructural evolution, small domains of interest were selected from the entire set of observed 3D microstructures based on X-ray CT, and struts of Ni foams with a hollow structure were simplified with relevant thin-solid struts. Numerical 3D modeling comprehensively disclosed that compression caused the transverse buckling of the struts, with the bending and buckling of struts thus reducing the stress. Thickness variation of the struts causes a change in the porosity of Ni-foams without a change in pore shape or connectivity. The overall range of strut thickness was from 59 to 133 μm, and the range of porosity values was from 80% to 93.7%. A stress drop was predicted with a decrease in the strut thickness or an increase in the porosity, as measured experimentally. It was also found that the stress drop contributed to an increase in the calculated energy absorption efficiency.

Effect of the Solid Phase Diffusion on the Mechanical Properties of Open-Cell Fe-Ni Alloy Foams

Compressive Property and Energy Absorption Characteristic of 3D Open-Cell Ni–Cr–Fe Alloy Foams under Quasi-Static Conditions

Synthesis and Properties of Open-Cell Ni–Cr–Fe–Al Alloy Foams by Pack Co-Deposition Process

Synthesis and mechanical properties of open-cell Ni-Fe-Cr foams

Microstructure, Oxidation Resistance and High-Temperature Strength of a New Class of 3D Open‐cell Nickel-Based Foams

Effect of Heat Treatment on the Microstructure, Compressive Property, and Energy Absorption Response of the Al–Mg–Si Alloy Foams

Electrical Conductivity of Open-Cell Fe–Ni Alloy Foams

Mechanical behaviors and energy absorption properties of Y/Cr and Ce/Cr coated open-cell nickel-based alloy foams

Analysis of Microstructure Evolution and Mechanical Properties during Compression of Open-Cell Ni-Foams with Hollow Struts Using Micro-CT and FEM

Experimental Study on Enhanced Ice Storage in Open-Cell Metal Foams

Enhanced Mechanical Properties of Novel Aluminum Foams Synergistically Reinforced by NiO Particles and in Situ Grown Carbon Nanotubes

Microstructural Influence on Compressive Behavior and Strain Rate Sensitivity of Open-Cell Nickel Foam

Fabrication and Compressive Behavior of Open-Cell Aluminum Foams Via Infiltration Casting Using Spherical CaCl2 Space-Holders

Temperature Effects on the Compressive Behaviors of Closed-Cell Copper Foams Prepared by Powder Metallurgy

Microstructure and Properties of NiTi Foams with 69% Porosity

Enhancement of the Mechanical Strength of Aluminum Foams by SiC Nanoparticles

Effect of Fe Addition on Microstructure and Properties of Al-3ni Alloys

Influences of Increased Pressure Foaming on the Cellular Structure and Compressive Properties of In Situ Al-4.5%Cu-xTiB2 Composite Foams with Different Particle Fraction

High temperature and mesostructure effect on aluminum foam compression responses

Improved energy absorption capacity of Al/Al 2 O 3 foams by the ductile/brittle hybrid deformation mode

Effect of the structure and volume fraction of nanophase on the mechanical properties of (FeNi)86B14 amorphous nanocrystalline alloys