Abstract:A joint chemical reactor system referred to as an ultrasonic-intensified micro-impinging jetting reactor (UIJR), which possesses the feature of fast micro-mixing, was proposed and has been employed for rapid preparation of FePO4 particles that are amalgamated by nanoscale primary crystals. As one of the important precursors for the fabrication of lithium iron phosphate cathode, the properties of FePO4 nano particles significantly affect the performance of the lithium iron phosphate cathode. Thus, the effects of joint use of impinging stream and ultrasonic irradiation on the formation of mesoporous structure of FePO4 nano precursor particles and the electrochemical properties of amalgamated LiFePO4/C have been investigated. Additionally, the effects of the reactant concentration (C=0.5, 1.0 and 1.5molL−1), and volumetric flow rate (V=17.15, 51.44, and 85.74mLmin−1) on synthesis of FePO4·2H2O nucleus have been studied when the impinging jetting reactor (IJR) and UIJR are to operate in nonsubmerged mode. It was affirmed from the experiments that the FePO4 nano precursor particles prepared using UIJR have well-formed mesoporous structures with the primary crystal size of 44.6nm, an average pore size of 15.2nm, and a specific surface area of 134.54m2g−1 when the reactant concentration and volumetric flow rate are 1.0molL−1 and 85.74mLmin−1 respectively. The amalgamated LiFePO4/C composites can deliver good electrochemical performance with discharge capacities of 156.7mAhg−1 at 0.1C, and exhibit 138.0mAhg−1 after 100 cycles at 0.5C, which is 95.3% of the initial discharge capacity.

Preparation of the Particle Size Controllable LiFePO4/C and Its Electrochemical Profile Characterization

High-performance Carbon-Coated LiMnPO4 Nanocomposites by Facile Two-Step Solid-State Synthesis for Lithium-Ion Battery

Rapid Preparation of High Electrochemical Performance LiFePO4/C Composite Cathode Material with an Ultrasonic-Intensified Micro-Impinging Jetting Reactor

Preparation and Electrochemical Properties of High-performance LiFePO_4

Optimized Performances of Core–shell Structured LiFePO4/C Nanocomposite

Olivine LiFePO4 Nanocrystallites Embedded in Carbon-Coating Matrix for High Power Li-ion Batteries

Mono-dispersed LiFePO4@C Core-Shell [001] Nanorods for a High Power Li-ion Battery Cathode

The Preparation and Characterization of LiFe<sub>0.98</sub>Ni<sub>0.01</sub>Nb<sub>0.01</sub>PO<sub>4</sub>/C by Carbon Reduction Route

The preparation and characterization of LiFe0.98Ni0.01Nb0.01PO4/c by carbon reduction route

The preparation and characterization of LiFe0.98Mn0.02PO4/C by spraydrying and low temperature reduction route

Nanostructure Optimization of LiFePO4/carbon Aerogel Composites for Performance Enhancement

Synthesis, characterization and properties of LiFePO4/C cathode material

Effects of particle size and carbon coating on electrochemical properties of LiFePO4/C prepared by hydrothermal method

Preparation and properties of LiFePO4/C composite materials with Fe2O3 as starting reactant

Synthesis and Electrochemical Performance of LiFePO4/C Prepared by a New Method

The Preparation and Characterization of LiFe<sub>0.98</sub>Mn<sub>0.02</sub>PO<sub>4</sub>/C by Spray-Drying and Low Temperature Reduction Route

Preparation and Electrochemical Performance of LiFePO_4/C Using Fe_2O_3 As Raw Material

Synergetic Effect of the Crystallinity, Particle Size of LiFePO4 and the In-Situ Introduced Fe2P on Its High-Rate Capability

Effects of carbon coating and iron phosphides on the electrochemical properties of LiFePO4/C

Synthesis of nano FePO 4 and electrochemical characterization of composite cathode material LiFePO 4/C

Investigation on a Core–shell Nano-Structural LiFePO4/C and Its Interfacial CO Interaction