Abstract:Abstract Recently, a new set of parameters produced by the Beckman-Coulter’s GEN’S, LH500, LH750 and the latest LH780 automated blood counters, derived from leukocyte and red cell’s morphological data by means of the VCS technology are available and can be printed as research data together with the leukocyte differential and reticulocyte analysis. With the use of these Research Population Data (RPD) parameters several recent publications have shown their usefulness for the diagnosis of malaria (Fourcade et al), sepsis (Chaves ), apoptosis detection (Lab hem 2005) and the diagnosis and differentiation of lymphoptoliferative disorders (Silva M et al) In order to evaluate the analytical behaviour of these newly described red blood cell and leukocyte morphological parameters in routine bood samples and in the Beckman-Coulter’s calibration and control 5C, we conducted a study to evaluate the paramters’ precision and performance during short and long term sample’s storage: Precision: 10 samples from normal individuals were analyzed 10 times and the CV for each parameter was calculated Short term stability stability at 4C and 22C: 5 normal samples were evaluated from the time of blood drawing until 5 hours later, both at room temperature (22C) and at 4 C Long term stability at 4C: 15 normal samples were evaluated at various times after blood drawing, from 4 hours (which was found to be the best time for sample analysis in the short term stability study, above) up to 77 hours after blood withdrawal. Control and Calibration with 5C: We evaluated the performance of the research parameters in the 5C by running the same batch of 5C control in 5 different counters from 4 different centers, comparing the results with those from 5 normal individuals Stability in a period of time: We have evaluated every week during two months 15 normal samples, recording the temperature and the avergae of all RPD values. RESULTS Precission: The CV% for the Mean Volume, Conductivity and Scatter of the different leukocyte types was always less than 1%, with an average of 0,6%. The CV% for the Standard Deviation of Volume, Conductivity and Scatter varied between 2.45% and 7.7%, wit an average of 4.9%. The CV% of any SD always being higher than the primary parameter. Short term stability: We observed no significant differences between samples kept at 4C and 22C during the first 5 hours after blood drawing. During the first two hours, however, minor fluctuations in results occurred, always <5%, being preferable to test the samples after blood stabilization, between 2 and 5 hours after withdrawal. Long term stability: The stability of the research parameters after 9 hours is best when the samples are kept at 4C, but the differences are not clinically significant up to 17 hours and, for some parameters, up to 24 hours after blood drawing. The comparison of the RPD research parameters from normal samples and from the Beckman’s 5C control showed good correlation in the different counters and the different centers. When the results from the 5C were higher or lower, the results from the normal samples were concordantly higher or lower respectively, The correlation coefficient was 0.98 for the Mean Volume and 0.92 for the Mean Conductivity The Stability of RPD values was acceptable during the period evaluated (2 m.)with changes lower than 3%. CONCLUSIONS: The results of the present study show that from the analytical stand point, precission, stability and possibility of calibration, these Research Population data are equivalent to those of other laboratory tests performed by modern instruments.

Study on setting up the reference method for the packed cell volume and its application

Performance Evaluation of the Sysmex CS-5100 Automated Coagulation Analyzer.

The Influence of Different Peripheral Venous Blood Sampling Methods on Hemolysis Rate in Emergency Room

Compare the accuracy and precision of Coulter LH780, Mindray BC-6000 Plus, and Sysmex XN-9000 with the international reference flow cytometric method in platelet counting

The possibility of automatic capillary blood testing in routine blood tests: an evaluation of the automatic mode of the Mindray BC-7500 CRP Auto Hematology Analyzer for capillary blood testing

Performance evaluation of the BC-720 auto hematology analyzer and establishment of the reference intervals of erythrocyte sedimentation rate in healthy adults

Platelet count evaluation compared with the immunoplatelet reference method and performance evaluation of the hematology analyzer Celltac G

Performance evaluation of routine blood and C-reactive protein analysis using Mindray BC-7500 CRP auto hematology analyzer

The Application of IFCC Reference Methods in Methodological Evaluation of Glycated Hemoglobin Measurement Systems

Correlation of various methods of hematopoietic progenitor cell estimation with standard flowcytometric CD34 enumeration

Analytical Features of the New Red Blood Cell and White Blood Cell LH750 Research Population Data.

[Survey and Establishment of the Hematological Parameter Reference Intervals for Adult in Xuzhou Area of China].

Establishment of a candidate reference measurement procedure for the enumeration of cell particles in urine and applied to multi-center evaluation of an automated urine analyzer

Evaluation for Clinical Application of UniCel DxH 800 Hematology Analyzer

Reference Method Applied to Assigning Values for Calibrators in Serum Gamma-Glutamyltransferase Assays

A-075 Development and Validation of Image-based Cell Counter Microscanner C3 for CD34-positive Hematopoietic Stem Cell Enumeration

Prediction of Viable CD34 Count in Harvested Product by Peripheral Blood Hematopoietic Progenitor Count of Automated Hematology Analyzer Undergoing Hematopoietic Stem Cell Transplantation

Hematopoietic Progenitor Cell Counting for Prediction of the Yield of Peripheral Blood Stem Cell in Mobilization and Harvest

Accuracy evaluation of PLT-F method on low concentration of platelet counting

Comparison of Performances of Five Capillary Blood Collection Tubes

Automated Measurement of Plasma Cell-Free Hemoglobin Using the Hemolysis Index Check Function