Abstract:Ultrafiltration hollow-fiber membranes were prepared from polyetherimide (PEI) with a wet spinning method. The effects of N,N-dimethylacetantide (DMAc) as a solvent additive in the internal coagulant and acetic acid as a non-solvent additive in the dope solution on the morphologies and performances of the membranes were investigated. The influences of PEI dope concentration on membrane morphologies and properties were also studied. Scanning electron microscopy (SEM) indicates that the addition of DMAc into the internal coagulant changes the inner fiber surface from a dense skin layer to a porous structure. However, the pure water flux of the membrane decreases with the increase of DMAc content. On the other hand, the addition of acetic acid into the casting solution promotes the spinodal demixing of the membratte-forming system and suppresses the macrovoid formation in the membrane. A nodular structure forms in the fiber skin layer. With increasing acetic acid content, the pure water flux of the membrane increases about 4-fold and the solute retention shows a slight decrease. The mechanical properties can also be improved slightly by this additive. The thermal resistance of the PEI ultrafiltration membranes prepared in this work was examined by hot water treatment at 80 degrees C. No change was observed in the permeation performance of the membranes, while the study of mechanical properties shows that the elongation-at-break of the membrane decreases slightly. PEI was sulfonated by chlorosulfonic acid (CSA) in 1,2-dichloroethane. With the increase of the molar ratio of CSA to PEI repeat unit and/or reaction time, the ion-exchange capacity (IEC) of the sulfonated polyetherimide (SPEI) increases accordingly. Water uptake test and contact angle measurements show that the hydrophillicity of the SPEI increases with the increase of the IEC. Polyetherimide/sulfonated polyetherintide (PEI/SPET) ultrafiltration hollow-fiber membranes were also prepared with a dry-wet phase inversion method and SPEI was used as a polymer additive. SEM study reveals that the addition of SPEI induces the formation of nodular structure and suppresses the formation of finger-like macrovoids. With the increase of air-gap distance, it was found that the number of micropores formed in the outer fiber surface and the pore size increased. On the other hand, the pure water flux of the membrane reaches a maximum and then decreases, while the solute retention decreases at first and then levels off at longer air-gap. Based on the filtration of bovine serum albuntin (BSA) solution, it was found that the use of SPEI in the blend membranes increased their hydrophilicity.

EFFECT OF ADDITIVES ON THE STRUCTURES AND PROPERTIES OF POLY (PHTHALAZINE ETHER SULFONE KETONE)(PPESK) ULTRAFILTRATION MEMBRANE

Preparation and characterization of improved fouling-resistant PPESK ultrafiltration membranes with amphiphilic PPESK-graft-PEG copolymers as additives

Development of High-Antifouling PPSU Ultrafiltration Membrane by Using Compound Additives: Preparation, Morphologies, and Filtration Resistant Properties.

Effect of pore-forming/hydrophilic additive anchorage on the mesoporous structure and sieving performance of a blended ultrafiltration (UF) membrane

Effect of PEG additive on the morphology and performance of polysulfone ultrafiltration membranes

Analysis of Additives on Hydrophilic Properties and Filtration Properties of Polysulfone Ultrafiltration Membrane

Formation kinetics and characterization of polyphthalazinone ether ketone hollow fiber ultrafiltration membranes

Preparation of poly(phthalazinone-ether-sulfone) sponge-like ultrafiltration membrane.

Effect of Additives on the Morphology and Performance of Symmetric Network PVDF Membranes

Preparation of a Poly(phthalazine Ether Sulfone Ketone) Membrane with Propanedioic Acid As an Additive and the Prediction of Its Structure

Preparation And Characterization Of Polysulfone Ultrafiltration Membrane With Peg As An Additive

Investigating the Impact of the Sulfonation Degree in Sulfonated Polyphenylsulfone (sPPSU) on PES/sPPSU Polymer Blend Membranes

Poly (phthalazinone Ether Sulfone Ketone) Properties and Their Effect on the Membrane Morphology and Performance

EFFECTS OF PEG600 AND OXALIC ACID ON PERFORMANCE OF PPESK HOLLOW FIBER UF MEMBRANE

Preparation And Performance Of Ultrafiltration Membranes From Polyetherimide And Its Sulfonated Derivatives

Preparation of Casting Solutions for Poly (phthalazinone Ether Ketone) Ultrafiltration Membrane

Molecular dynamics coupled with experimental study of the effects of polyethylene glycol on the structure and antifouling properties of polyethersulfone membranes

Hydrophilic modification of poly(phthalazine ether sulfone ketone) ultrafiltration membranes by the surface immobilization of poly(ethylene glycol) acrylates

Effect of PEG Additives on Properties and Morphologies of Polyetherimide Membranes Prepared by Phase Inversion

Separation performance enhancement of PEEKWC/PEI cross-linked ultrafiltration membranes by poly(ethylene glycol) and polyvinylpyrrolidone as polymeric additives

Effect of Polyethlene Glycol on Membrane Forming Systems and Polyethersulfone with Cardo Performance and Structure