Abstract:The material extrusion 3D printing process known as fused deposition modeling (FDM) has recently gained relevance in the additive manufacturing industry for large-scale part production. However, improving the real-time monitoring of the process in terms of its mechanical properties remains important to extend the lifespan of numerous critical applications. To enhance the monitoring of mechanical properties during printing, it is necessary to understand the relationship between temperature profiles and ultimate tensile strength (UTS). This study uses a cyber–physical production system (CPPS) to analyze the impact of four key thermal parameters on the tensile properties of polylactic acid (PLA). Layer thickness, printing speed, and extrusion temperature are the most influential factors, while bed temperature has less impact. The Taguchi L-9 array and the full factorial design of experiments were implemented along with the deposited line's local fused temperature profile analysis. Furthermore, correlations between temperature profiles with the bonding strength during layer adhesion and part solidification can be stated. The results showed that layer thickness is the most important factor, followed by printing speed and extrusion temperature, with very close influence between each other. The lowest impact is attributed to bed temperature. In the experiments, the UTS values varied from 46.38 MPa to 56.19 MPa. This represents an increase in the UTS of around 17% from the same material and printing design conditions but different temperature profiles. Additionally, it was possible to observe that the influence of the parameter variations was not linear in terms of the UTS value or temperature profiles. For example, the increase in the UTS at the 0.6 mm layer thickness was around four times greater than the increase at 0.4 mm. Finally, even when it was found that an increase in the layer temperature led to an increase in the value of the UTS, for some of the parameters, it could be observed that it was not the main factor that caused the UTS to increase. From the monitoring conditions analyzed, it was concluded that the material requires an optimal thermal transition between deposition, adhesion, and layer solidification in order to result in part components with good mechanical properties. A tracking or monitoring system, such as the one designed, can serve as a potential tool for reducing the anisotropy in part production in 3D printing systems.

Research on Effect of Operating Parameters of Calcium Carbonate-plastic Twin-screw Extruder on Tensile Strength of Sheet Material

Influence of Hot Press Molding Parameters on the Tensile Strength of Bamboo Fiber/PLA Composites

Finite Element Analysis and Optimal Researchon Plasticizing Capacity of Screws

Effects of Processing Temperature on the Mechanical Properties of Calcium Carbonate-Plastic Composite Packaging Materials

Experimental investigation and optimization of process parameters on tensile strength of carbon coated PLA material

Influences of Process Parameters on Mechanical Properties of ABS/Aluminum Powder Blending Products

Machine Learning Study of the Effect of Process Parameters on Tensile Strength of FFF PLA and PLA-CF

Design of Experiments to Compare the Mechanical Properties of Polylactic Acid Using Material Extrusion Three-Dimensional-Printing Thermal Parameters Based on a Cyber–Physical Production System

Experimental study of the effect of different 3D printing parameters on tensile strength, using artificial neural network

Numerical Simulation and Process Optimization of Internal Thread Cold Extrusion Process

Research on relationship between geometrical dimensions and elongation of Polycarbonate tensile specimen

Effect of Printing Parameters on the Mechanical Properties of Parts Fabricated with Open-Source 3D Printers in PLA by Fused Deposition Modeling

Effects of manufacturing process and surface treatments on mechanical properties of PLA/SCF composites using extrusion printing

Experimental investigation of process parameters in polyether ether ketone 3D printing

Applying the Taguchi Method to Improve Key Parameters of Extrusion Vacuum-Forming Quality

Optimization of Injection Molding Processing Parameters of Display Shell Based the Orthogonal Experiment

Optimizing process parameters of fused deposition molding for 3D printing customized control of polyetheretherketone scaffolds

Studying the effects of FDM process parameters on the mechanical properties of parts produced from PLA using response surface methodology

Effect of Process Parameters on Tensile Mechanical Properties of 3D Printing Continuous Carbon Fiber-Reinforced PLA Composites

Effect of process parameters of fused deposition modeling on mechanical properties of poly-ether-ether-ketone and carbon fiber/poly-ether-ether-ketone

Effect of Printing Parameters on the Thermal and Mechanical Properties of 3D-Printed PLA and PETG, Using Fused Deposition Modeling