Abstract:Drying is a very important unit operation in many industries such as food, pharmaceuticals, chemicals and ceramics. In most cases, wet materials are dried by forced convection using hot air flow. Heat and mass transfer processes during drying have been studied by both experimental and numerical simulation methods. For the purpose of studying the mechanism of heat and mass transfer and stress-strain distribution during the hot air drying of biological porous medium, two-way coupled thermo-hydro-mechanical mathematical model has been developed to simulate the hot air convective drying process of biological porous media on basis of Fickian diffusion theory, Fourier’s law of heat conduction and thermoelasticity mechanics. The following assumptions were made in order to find a solution to the hot air drying model: the biological porous medium was homogeneous and isotropic; the deformation during drying was elastic. The transient model, composed of a system of partial differential equations, was solved by finite difference methods. The computational procedure was programmed using C language. Some physical and mechanical properties of carrot changing with dry basis moisture content and temperature were considered. The numerical results were compared with available experimental data obtained during the drying of potatoes and carrots. The relative errors between numerical results and experimental data were both less than 5%, which showed the numerical results obtained using the mathematical model were in good agreement with the experimental data. Numerical simulations of the drying curve variations and the spatio-temporal distributions of moisture, temperature and drying stresses and strains of carrot were also evaluated. The temperature and moisture content showed a gradient inside carrot slice during drying. As the drying process proceeded, the temperature inside the carrot slice initially increased to reach the wet bulb temperature of the environment and eventually leveled off. The dry basis moisture content inside the carrot slice decreased, with the fastest decreased at the heat and mass transfer interface, eventually reached the equilibrium moisture content of the potato and leveling off. Both the moisture content gradient and the temperature gradient decreased gradually in the thickness direction. The normal stress was negative in all parts of the carrot slice, and the larger the closer to the evaporation interface. The shear stress was positive in all parts of the carrot slice, and the maximum shear stress occurred in the middle of the carrot slice. As in the case of the normal stress, the values of the normal strain were negative. The change trend of normal strain with time was consistent with that of moisture content. These results indicated that the observed physical deformations were caused by the dehydration of carrot slice during drying. The influence of drying conditions, such as air temperature, air velocity and the thickness of porous media on drying process was analyzed. Analysis showed that under certain drying conditions, the higher air temperature, the greater air velocity and the thinner slice thickness, the shorter drying time. This work should help in developing an understanding of the relationship between mass and heat transfer, shrinkage, stress, strains and physical degradation.

Mathematical Modeling for Thin Layer Vacuum Belt Drying of Panax Notoginseng Extract

Optimization for vacuum belt drying process of Panax notoginseng extract

Quality Evaluation of Panax Notoginseng Extract Dried by Different Drying Methods

Microwave Vacuum Drying Properties and Kinetics Model of Radix Paeoniae Rubra Extract

Optimization for Vacuum Belt Drying Process of Rehmannia Leaves Extract

Optimization for vacuum belt drying process of Radix Salvia Miltiorrhiza extract

Modeling of Muti-layer Far-Infrared Dryer

A novel mechanical vapor compression vacuum belt drying system: Model development, experimental verification and performance prediction

Mathematical modeling of thin layer drying of carrot slices by forced convection

Optimization of Microwave Vacuum Low-temperature Drying Process for Rehmannia Glutinosa Libosch Leaves Extract

The simulation analysis and experiment of drying thin-layer radish strips

A fully coupled multiphase model for infrared-convective drying of sweet potato

Modeling of carrot thin layer convective drying process

Mathematical Model and Numerical Simulation of Biological Porous Medium During Hot Air Drying

Research on boiling heat transfer of aqueous extracts vacuum drying based on fractal theory

[Study on Extraction Kinetics of Salviae Miltiorrhizae Radix Et Rhizoma: Model Establishment and Investigation of Critical Process Parameters].

Chromatographic elution process design space development for the purification of saponins in Panax notoginseng extract using a probability-based approach.

American Ginseng Slice Drying and Optimization: Effect of Different Drying Methods on Drying Kinetics and Physicochemical Properties

Improving Drying Characteristics and Physicochemical Quality of Angelica sinensis by Novel Tray Rotation Microwave Vacuum Drying

Simultaneous Application of Vacuum and Infrared Drying to Whole Drying Process of Bitter Gourd Slices: Design, Drying Kinetics, Experiment, Characteristic, Energy Aspect

Mathematical Models' Establishment of Hot-Air Drying for Spratelloides Gracilis