Abstract:It is well known that free radical (co)-polymerization of multivinyl monomers (MVMs) leads to insoluble gels even at a low monomer conversion, and the gelation point can be predicted by Flory-Stockmayer theory (F-S theory) based on two assumptions: (1) equal reactivity of all vinyl groups and (2) the absence of intramolecular cyclization. This theory has been experimentally studied and o.o verified with conventional free radical (co)polymerization (FRP) of several MVMs (e.g., divinylbenzene, DVB). However, it is still debatable whether this theory is applicable for the polymerization of MVMs using reversible deactivation radical polymerization (RDRP) approaches, such as atom transfer radical polymerization (ATRP). Herein, Monte Carlo simulations using two statistical models-with cyclization (w.c.) and without cyclization (wo.c., corresponding to F-S theory)-and dynamic lattice liquid (DLL) models were conducted to study ATRP of divinyl monomers. The simulated gel points using w.c. and wo.c. models were compared with those obtained from ATRP experiments, from calculation using F-S theory, and from simulations using DLL models. The molecular weights, dispersity, and extent of intermolecular/intramolecular cross-linking were calculated as a function of double bond and cross-linker conversion. The results demonstrated that the gel points obtained from both w.c. and wo.c. models were lower than the values from DLL models and experiments. This indicates that F-S theory cannot be used to accurately predict the polymerization of divinyl monomers via ATRP. Our study shows that the limitation of F-S theory in predicting ATRP reaction of divinyl monomers is not only due to neglecting intramolecular cyclization but also due to spatial restrictions which can cause the reactivity and accessibility of vinyl groups becoming nonequivalent in ATRP of divinyl monomers.

A Theoretical Model for Anionic Polymerization of Polar Monomers Initiated by Electron Transfer

Kinetics and Modeling of Solution Arget Atrp of Styrene, Butyl Acrylate, and Methyl Methacrylate

Modeling for the Diffusion Limitation of Free Radical Polymerization

Nonsteady‐state Kinetics for Anionic Polymerization of Polar Monomer Initiated Instantaneously by Electron Transfer

Nonsteady State Analysis for the Kinetics of Anionic Polymerization of Polar Monomers

Experiment and Simulation on Styrene Polymerization with Linear Bifunctional Initiator 2,5-Dimethyl-2,5-di(2-ethylhexoylperoxy)hexane (Dmdehph)

Kinetic Model for Lonic Polymerization Initiated by Difunctional Initiator with Monomer Transfer

A Molecular Dynamics Model Of The Amorphous Regions Of Polyethylene Oxide

Kinetic Model for a Polymerization Process Where the Rate Constants of Both Propagation and Termination by Monomer Depend on Chain‐length

Kinetic Modeling of Surface-Initiated Atom Transfer Radical Polymerization

Kinetic Theory of Anionic Copolymerization with Constant Monomer Ratio, 2 . Molecular Weight Distribution

Graphical Method for Polymerization Kinetics. II. Influence of Monomer Transfer on Molecular Weight Distribution for Anionic Polymerization Initiated by Multifunctional Initiator

A New View of the Initiation and Propagation in Anionic Polymerization

Nonsteady-State Model for Kinetics of Radical Chain Polymerization .1. Direct Photoinitiation and Thermal Initiation with Constant Monomer Concentration

Kinetics Theory of Anionic Copolymerization with Constant Monomer Ratio, 1. Sequence Distribution

Determining the Kinetic and Thermodynamic Parameters of Anionic Polymerization of Styrene Using Linear Free‐Energy Relationship

Monte Carlo Simulations Of Atom Transfer Radical (Homo)Polymerization Of Divinyl Monomers: Applicability Of Flory-Stockmayer Theory

Theoretical Study of Sequence Distributions in Polydienes. III. Kinetic Treatment of First‐order Markovian Process

KINETICS OF STYRENE POLYMERIZATION INITIATED BY DIFUNCTIONAL INITIATOR

KINETIC MODEL OF FREE RADICAL POLYMERIZATION INCLUDING DIFFUSION PHENOMENA

Modelling and Kinetic Study on Radical Polymerization of Methyl Methacrylate in Bulk, 1. Propagation and Termination Rate Coefficients and Initiation Efficiency