Abstract:A phenomenon seemingly unique to hybrid miniemulsion polymerization was observed where monomer conversion would either plateau at a limiting value or quickly switch to a dramatically lesser rate. This phenomenon has been attributed to a combination of three factors. The first factor is the degree to which the monomer and resinous component are compatible. Second is the resultant particle morphology after circa 80% monomer conversion, which roughly corresponds to the portion of reaction where this morphology is established. The third factor is the degree of interaction between the growing polymer and resin (grafting). Of these three, the first two factors were found much more significant in contributing to the limiting conversion. When particle morphology was found to be core/shell, a hard shell (high T-g polymer, PMMA) was found to form a barrier against newly formed initiator radicals derived in the aqueous-phase after appropriate conversion. Residual unreacted monomer solubilized in the resin-dominated particle core was thereafter unreachable by new radicals; hence a limited monomer conversion. In cases where the acrylic polymer (PBA) exhibited a glass transition significantly below the reaction temperature, instead of a core/shell morphology one where the acrylic polymer (and monomer) comprised the continuous particle-phase with small internal resinous island domains was observed. A portion of the monomer concentration was again found to be solubilized within the resin domains, yet in this case newly formed initiator radicals encountered a viscous environment instead of an effective barrier. Rate was found to be limited by the feed of monomer to local polymerization in the continuous particle phase from those resinous islands where residual monomer is solubilized. This is what led to continued polymerization, but at a considerably lesser rate.

Modeling and Simulation of Semibatch Emulsion Polymerization

Kinetics and modeling of semi-batch RAFT copolymerization with hyperbranching

Modeling for the Diffusion Limitation of Free Radical Polymerization

Graft Copolymerization of Styrene and Acrylonitrile in the Presence of Poly(propylene Glycol): Modeling and Simulation of Semi‐Batch and Continuous Processes

110Th Anniversary: Model-Guided Preparation of Copolymer Sequence Distributions Through Programmed Semibatch RAFT Mini-Emulsion Styrene/Butyl Acrylate Copolymerization

Targeting Copolymer Composition Distribution Via Model-Based Monomer Feeding Policy in Semibatch Raft Mini-Emulsion Copolymerization of Styrene and Butyl Acrylate

Design and Control of Copolymer Composition Distribution in Living Radical Polymerization Using Semi‐Batch Feeding Policies: A Model Simulation

Modeling and Experimentation of RAFT Solution Copolymerization of Styrene and Butyl Acrylate, Effect of Chain Transfer Reactions on Polymer Molecular Weight Distribution

Graft Copolymerization of Styrene and Acrylonitrile in the Presence of Poly(propylene glycol): Kinetics and Modeling

Simulation Studies on the Origin of the Limiting Conversion Phenomenon in Hybrid Miniemulsion Polymerization

Kinetic Model of Semibatch Polymerization with ABg Monomer and Bƒ Core

Free radical seeded emulsion polymerization with participation of hydrolysis-condensation reaction ( Ⅱ ) Parameters and modeling application

Predictive model of polymer reaction kinetics and coagulation behavior in seeded emulsion co- and ter-polymerizations

The Combined Statistical and Kinetic Modeling of Gel/Sol Partition in Free-Radical Copolymerization of Vinyl/Divinyl Monomers

Experiment and Simulation on Styrene Polymerization with Linear Bifunctional Initiator 2,5-Dimethyl-2,5-di(2-ethylhexoylperoxy)hexane (Dmdehph)

Dynamic Optimization of Batch Free Radical Polymerization with Conditional Modeling Formulation Through the Adaptive Smoothing Strategy

A model of the gel fraction of polymer in the vinyl chloride/divinyl monomers suspension copolymerization

On the Mathematical Modeling of Emulsion Polymerization Reactors

Modeling of Effective Crosslinking Density of the Gel in Free-Radical Copolymerization of Vinyl/divinyl Monomers

Kinetic and Molecular Weight Control for Methyl Methacrylate Semibatch Polymerization. II. Open Control

Mathematical Modeling and Simulation of Vinylidene Fluoride Emulsion Polymerization