Analysis and Summary on the New Power Products from National Semiconductor
Yan Hui-Qiong,Du Si-dan
DOI: https://doi.org/10.3321/j.issn:0469-5097.2007.01.005
2007-01-01
Abstract:This paper analyzes power products from National Semiconductor. They can be separated into two kinds approximately: low-dropout regulator (LDO) and switching regulator. LDO is current-controlling regulator. Its input to output voltage drop is reduced below 0.5~0.6V. It has better performance compared with traditional 3-terminal regulator. It is a mini-size system-on-chip, which has low cost. It has very low quiescent current and its output voltage is very accurate. The application circuit is very simple, and its requirements of output capacitor and inductors are low. The LDO provides very low noise performance with low grand pin current in an extremely small package. It enables low voltage ripper. Also it has simple and fast enable control. A high (or low) level can make it working or shutting down. It has a high proportion of capability and power, and is very suitable for electronic equipments, which need low noise and low cost. The feature of switching regulator is high efficiency and saving power. It leads the developing direction of stabilized voltage power supplies, and it has been the main products in voltage regulators. Switching regulator utilizes field effect tube (FET) as a switch. It regulates the output voltage by Controlling duty ratio of the switch. Using power transistor as an example, voltage drop between the collector and the emitter is close to zero when FET fully turns on. And its current in the collector is zero when FET turns off. The key components in switching regulator are operated at high switching frequency, so the power consumption is very low, and the efficiency can achieve 80%~90%. These products use advanced architects and have very small package. It enables low voltage ripper on both the input and the output. With a very high switching frequency, the inductors and output capacitor can be physically small and low cost. The conductors hawe the features of small area and light weight. High efficiency is achieved through the use of FET. And because of low cost, the temperature increasing is light. It increases stability and reliability of the whole circuit. Because of different energy-storage elements, the switching regulator can be divided into two kinds. One is DC/DC converter based on the inductor, the other is converter based on the capacitor. DC/DC converter based on the inductor has integrated switch FET. It utilizes an input and output inductor to storage energy. And it provides relatively high power converting efficiency in all DC/DC converting methods. But it needs more area compared with most linear methods and some methods based on the capacitor in the condition of the same output current. It is very suitable for the applications whose current is over 300 mA. And it can carry out voltage buck, boost or buck-boost topology. DC/DC converter based on the capacitor utilizes switching array, logical circuit and comparing controller to step up the voltage. And it uses capacitor to storage energy. The inductor is not needed in this kind of regulator. Its working frequency is very high, so mini-type capacitor (1μF) can be used. It needs small area and low using cost. Inner FET switching array controls “fast” voltage charge and discharge of the capacitor. So output voltage can be gained from input voltage by multiplying modulus such as 0.5, 2, 3, 4 and so on. This method can achieve efficiency up to 90%. The converter can supply output voltage ±2 times as the input voltage only using outside capacitor. Its cost is mainly from the ESR (equivalent series resistance) of the capacitor and R_ DS(ON) of the inner switching transistor. And because the converter based on capacitor dose not need inductor, its radiation can be neglected. Battery charge management and LED light driver are also introduced in this paper. Take LP3947 as an example. It is a complete charge management system that safely charges and maintains a Li-Ion battery from either USB power source or AC adaptor. In USB mode, the LP3947 supports charging in low power or high power mode. Alternatively, the LP3947 can take charge from AC adaptor. In both USB and AC adaptor modes, charge currenu, battery regulation voltage, and End of Charge (EOC) point can be selected via I2C interface. The charger also has under-voltage and over-voltage protection as well as an internal 5.6 hr timer to protect the battery. And conductor such as LP3943 is an integrated device capable of independently driving LEDs. This device also contains an internal precision oscillator that provides all the necessary timing required for driving each LED. Two prescaler registers along with two PWM registers provide a versatile duty cycle control. The LP3943 contains the ability to dim LEDs in SMBUS/ I2C applications where it is required to cut down on bus traffic. They can do well in modern portable applications such as mobile telephone and palmtop/laptop computer and so on. The input and output parameter, function and typical application circuit will be analyzed in this paper.