Abstract:To synergistically improve the strength-ductility of copper alloys used in the miniaturized component, Cu-3.2Ti-0.2Fe-0.2V alloy with heterogeneous structure was obtained by thermo-mechanical treatment (namely, short-time annealing). The heterogeneous structure was composed of the non-uniform grains formed due to Laves phase inhibiting grain growth and FCC structured Cu4Ti phase with good coherent interface precipitated on the grain boundaries in sub-micro size. After aging at 400 °C for 2 h and then 450 °C for 4 h, the ultimate tensile strength and elongation of the heterogeneous-structured alloy were 976.8 MPa and 18.8% respectively, which was approximately 120 MPa more than that of the coarse-grained alloy after complete annealing, but both alloys had comparable ductility. When cold-rolling with 5% reduction was carried out before the aging of 450 °C, the strength increased to 1057 MPa and corresponding elongation was still over 10%. The strengthening mechanism of alloy with heterogeneous structure was analyzed and the hetero-deformation induced hardening of 284.5 MPa was the other significant reinforcement. The semi in-situ observation of tensile deformation behavior shown that the superior ductility in coarse-grained alloy was mainly attributed to the slipping and twinning. While grain rotation and grain boundary sliding were additional deformation mechanism in heterogeneous-structured alloy during tensile deformation, meanwhile, the texture of S, {110}<1 1 ‾ 1> and {331}<1 2 ‾ 3> components converted to the texture of {441}< 1 ‾ 1 ‾ 8>, Goss, Copper and {012}< 8 2 ‾ 1 > components. The deteriorative ductility after rolling with the reduction of 5% was owing to the S and Cube components converted to the strong texture of {032}<22 3 ‾ > components.

Effects Of Microstructure On Tensile Strength Of Electroformed Copper

High Strength and High Ductility Copper Obtained by Topologically Controlled Planar Heterogeneous Structures

The microstructure and mechanical properties of copper in electrically assisted tension

Mechanical Properties and Microstructure of Rolled and Electrodeposited Thin Copper Foil

Processing and Specimen Thickness to Grain Size (t/d) Ratio Effects on Tensile Behaviour and Microformability of Copper Foils

Tensile strength and Young's modulus of Cu-Ag alloys in the evolution of microstructure into filamentary composites

Microstructure evolution and properties of Cu–Ag microcomposites with different Ag content

EFFECTS OF Ag CONTENT ON MICROSTRUCTURE AND PROPERTIES OF THE FILAMENT STRENGTHENED Cu-Ag ALLOYS

Investigation of the Dendritic Structure Influence on the Electrical and Mechanical Properties Diversification of the Continuously Casted Copper Strand

Relationships between mechanical strength and electrical conductivity for Cu–Ag filamentary microcomposites

Research and Development on Microstructure, Properties and Alloying of Cu-Ag Filamentary Composites

A Study on the Microstructural Evolution, Interfacial Diffusion and Mechanical Properties of Ultra-thin Stainless Steel–Copper Composites Fabricated by Roll Bonding

Effects of microstructure and texture on the deep drawability of C10200 copper sheets

Effect of Scanning Mode on Microstructure and Physical Property of Copper Joint Fabricated by Electron Beam Welding

Microstructure evolution in Cu-2.13Fe-0.026P (wt%): The contribution of texture intensity to residual stress variation

Microstructure evolution of high-strength and ultra-high-conductivity microfilament wire prepared by continuous deformation of single-crystal copper

Microstructure and Texture of Pure Copper under Large Compression Deformation and Different Annealing Times

Microstructures and mechanical properties of Cu–Ti alloys with ultrahigh strength and high ductility by thermo-mechanical treatment

Effect of annealing temperature on microstructure and tensile properties of copper/aluminum composite thin strip

Effects of Scanning Mode on Microstructure and Mechanical Properties of Copper Joint Fabricated by Electron Beam Welding

Quantitative Study on the Evolution of Microstructure, Strength, and Electrical Conductivity of the Annealed Oxygen‐Free Copper Wires