Abstract:Phase-transformations and microstructural evolution during and after inter-critical annealing of a low-alloy, dual-phase steel are studied utilizing dilatometric measurements, and microstructural characterization methods, including scanning electron microscopy, synchrotron X-ray diffraction, and atom-probe tomography. Dilatometric measurements reveal that the sample contains ~72% austenite, after annealing for 5-min at 871 oC, which agrees with the water-quenched microstructure, and ~90% after further annealing to 1 h, which agrees with thermodynamic predictions. A continuous-cooling transformation (CCT) diagram is constructed, within the cooling-rate range between 1 oC/s and 70 oC/s. The incubation time for the ferrite-transformation is <1 s, after inter-critical annealing, and the secondary-phases are mainly pearlite for cooling-rates of <5 oC/s, and martensite for cooling-rates >10 oC/s, which is confirmed utilizing scanning electron-microscope observations. The microhardness increases as the cooling rate increases, and an abrupt slope-change is explained by the major secondary-phase changing from martensite to pearlite between 5 oC/s and 10 oC/s. Atom-probe tomography demonstrates the coexistence of martensite and pearlite as secondary-phases for 30 oC/s and a switch in austenite-ferrite transformation mechanisms from para-equilibrium (70 oC/s) to partitioning local-equilibrium (30 oC/s). A microstructural map is constructed to reveal the austenite decomposition products in the cooling-rate range between 1 oC/s and 70 oC/s. Based on composition measurements of the matrix, utilizing APT, the effects of cooling-rates on solid-solution-strengthening are estimated, and the results demonstrate that solid-solution strengthening, especially carbon-redistribution, accounts for the majority of the strength variations due to different cooling-rates. (239 words)

In-situ Observation of Solid Phase Transformation of a low Carbon Steel

In situ observation of the austenite to ferrite transformation in low-carbon steels from different initial phases at defined cooling rates

In Situ Observation of Martensitic Phase Transformation in Low Carbon Steel Containing Cu

In Situ Observation of Phase Transformation and Structure Evolution of a 12 Pct Cr Ferritic Stainless Steel

Effect of Cooling Rate on High Temperature δ→γ Phase Transformation in Low Carbon Silicon-Bearing Steel

In Situ Observation of Bainite to Austenite Transformation of Microalloyed High Strength Steel During Simulated Welding Cycle

In-situ Observation of Phase Transformation During Heat Treatment Process of High-Carbon Bainitic Bearing Steel

Phase transformation and microstructure evolution of pearlite heat-resistant steel during heating

In situ observation of bainite transformation of low carbon Si-Mn steel

Effects of Cooling Rate and Vanadium on δ→γ Phase Transformation in Low Carbon Steel

Continuous cooling transformation curve of Cu bearing low carbon steel andin-situ observation of its martensitic transformation

Atom-probe tomographic and dilatometric studies of phase-transformations after inter-critical annealing of a low-carbon dual-phase steel

Study on Bainitic Transformation by Dilatometer and in Situ LSCM

Cascading phase transformations in situ for the simulated coarse-grained heat-affected zone of P92 heat-resistant steel

In Situ Observation of Bainitic Transformation Behavior in Medium Carbon Bainitic Steel

Combined Martensite and Bainite Formation from Austenite Decomposition in HSLA Steel

Research on the Phase Transformation of a Newly Developed Carbonitride-Strengthened Martensitic Heat Resistant Steel

In Situ Observation of Austenite–ferrite Interface Migration in a Lean Mn Steel During Cyclic Partial Phase Transformations

In-Situ Observation of β→α Phase Transformation of TA2 Commercial Pure Titanium during Continuous Cooling

Continuous Cooling Phase Transformation Rule of 20crmnti Low-Carbon Alloy Steel

In-Situ Observation On The Influences Of Ti On Phase Transformation Of Weld Metal Processed By High-Heat Input Welding