Abstract:In this paper, the start microstructure of full martensite and dual phases comprising ferrite and martensite were introduced into quenching and partitioning (Q&P) steel to tailor the microstructural characteristics and mechanical behaviors, which was achieved by means of a pre-quenching treatment with various temperatures. It is revealed that the conventional Q&P sample possessed bimodal microstructure with predominantly blocky feature, while gradually changed from combination of blocky and lath structures into individually lath feature in pre-quenched Q&P samples. The reversed austenite presented different variants, which predominantly reproduced the orientation of parent austenite and occasionally possessed twin relationship, low angle misorientation or extraneous with parent austenite. The twin-related austenite included annealing twin and reversed twin, whilst the latter showed twin relationship with both neighbored annealing twin and parent austenite. The variant type of reversed austenite significantly influenced the characteristics of its orientation relationship with neighbored pre-quenched martensite. The pre-quenching treatment was favorable to improve the carbon content of meta-stable austenite before Q&P treatment, while the final carbon content in retained austenite was mainly controlled by the synergistic carbon partitioning of martensite and bainite on basis of thermodynamic calculation, accompanied with the partitioning of Mn and Si elements. Moreover, the pre-quenched martensite deformed coordinately in a unit of martensite packet and was beneficial to retard necking to improve ductility. The optimal mechanical properties were obtained with pre-quenching temperature near Ac 3 , possessing yielding strength of 623 MPa, ultimate tensile strength of 861 MPa and product of strength and elongation exceeding 28 GPa%, attributing to the positive TRIP effect originating from lath-like retained austenite with high carbon content and multi-level hierarchical microstructure inherited from pre-quenched martensite.

In Situ Observation of Martensitic Phase Transformation in Low Carbon Steel Containing Cu

Microstructural Evolution of a Low-Carbon Steel during Application of Quenching and Partitioning Heat Treatments after Partial Austenitization

Cu partitioning behavior of Fe-C-Mn-Cu steel by I & Q process

Cu Partitioning Behavior and Its Effect on Microstructure and Mechanical Properties of 0.12C-1.33Mn-0.55cu Q&P Steel

In situ observation of bainite transformation of low carbon Si-Mn steel

In situ observation of the austenite to ferrite transformation in low-carbon steels from different initial phases at defined cooling rates

In Situ Observation of the Grain Growth Behavior and Martensitic Transformation of Supercooled Austenite in NM500 Wear-Resistant Steel at Different Quenching Temperatures

Insight into austenite reversion and mechanical behavior of quenching and partitioning steel inherited hierarchical structure of martensite

The austenite to polygonal ferrite transformation in low-alloy steel: multi-phase-field simulation

Effect of Cu Partitioning Time on Microstructure and Properties of Steel with I&Q&P Treatment

Early Martensitic Transformation in a 0.74C–1.15Mn–1.08Cr High Carbon Steel

Experimental and theoretical analysis of multiphase microstructure in a newly designed MnSiCrC quenched and partitioned steel to promote bainitic transformation: The significant impact on mechanical properties

Phase transformation and microstructure evolution of pearlite heat-resistant steel during heating

In Situ Observation of Thermoelastic Martensitic Transformation of Cu-Al-Mn Cryogenic Shape Memory Alloy with Compressive Stress

Investigation of microstructural evolution and bainite transformation kinetics of multi-phase steel

Phase-field simulation and high-temperature confocal laser scanning microscope experimental study of Martensite transformation during the disk laser quenching process

Atom-probe tomographic and dilatometric studies of phase-transformations after inter-critical annealing of a low-carbon dual-phase steel

In-Situ Observation On The Influences Of Ti On Phase Transformation Of Weld Metal Processed By High-Heat Input Welding

Effect of quenching and partitioning on the microstructure evolution and electrochemical properties of a martensitic stainless steel

Formation of Microstructure in Advanced Low-Carbon Steel of Martensitic Class Under Heat Treatment

Microstructure Transformation on Pre-Quenched and Ultrafast-Tempered High-Strength Multiphase Steels