Abstract:Zhang, Zhenlin ; Xiao, Ying ; Xu, Jun ; Li, Chao ; Tan, Feng-Liang ; Luo, Yajun ; Liu, Kecai ; In this study, Al-Si-Cu-Mg composites reinforced with Silicon carbide (SiC) particles and/or Carbon nanotubes (CNTs) were fabricated using semi-solid stirring casting technology (SSC). The aim of the study was to investigate the influence of SiC and/or CNTs on the mechanical properties, microstructural evolution, and deformation mechanisms of the Al-Si-Cu-Mg alloy. The findings indicated that the presence of SiC/CNTs in the composite had a significant effect on refining the α-Al phase and altering its grain orientation. Additionally, the results obtained from EBSD and TEM revealed that the microstructure of the Al-Si-Cu-Mg-SiC/CNTs hybrid composite (HAMC) underwent dynamic recrystallization (DRX) and static recrystallization (SRX), resulting in a fine equiaxed recrystallized structure. This process also led to the formation of high-angle grain boundaries (HAGBs) through dislocation rearrangement. The SiC particles were evenly distributed within the matrix, ensuring good interface bonding between SiC and α-Al phases. Moreover, the CNTs reacted with the matrix, resulting in the in-situ formation of the Al4C3 phase at the interface. The addition of SiC/CNTs significantly increased the tensile strength of HAMC at 25°C and 250°C, from 319MPa and 178MPa to 438MPa and 331MPa. Examination of the fracture surface of the hybrid composite unveiled that void formation occurred primarily at the regions surrounding the matrix-particle interface.

Fabrication of Al-based hybrid composites reinforced with SiC whiskers and SiC nanoparticles by squeeze casting

Fabrication and Evaluation of Al-based Hybrid Composites Reinforced with SiC Whiskers and SiC Nanoparticles

Microstructure and Tensile Properties of Al Hybrid Composites Reinforced with SiC Whiskers and SiC Nanoparticles

Compressive behaviour of Al-based hybrid composites reinforced with SiC whiskers and SiC nanoparticles

Squeeze casting technique for fabricating SiCp/Al composites with lower volume fractions of SiC particles

Sicp/Al Composites Fabricated by Modified Squeeze Casting Technique

Fabrication and characterization of SiC whisker reinforced reaction bonded SiC composite

The properties and microstructure of hybrid composites reinforced with WO3 particles and Al18B4O33 whiskers by squeeze casting

Fabrication, Microstructure and Mechanical Properties of a SiCw/ZK51A Mg Composite by Semi-Solid Extrusion Directly Following Liquid Infiltration

Fabrication and Mechanical Properties of SiCw(p)/SiC-Si Composites by Liquid Si Infiltration using Pyrolysed Rice Husks and SiC Powders as Precursors

Fabrication and characteristic of Al-based hybrid composite reinforced with tungsten oxide particle and aluminum borate whisker by squeeze casting

Microstructure Evolution and Mechanical Behaviors of SiCp/CNTs Hybrid Reinforced Al-Si-Cu-Mg Composite by Semi-solid Stir Casting

Fabrication and mechanical properties of high-volume-fraction Si 3 N 4 -Al-based composites by squeeze infiltration casting

MICROSTRUCTURE AND PROPERTIES OF DEFORMABLE SiCP/Al COMPOSITE FABRICATED BY SQUEEZE CASTING METHOD

Strengthening Behavior in SiC Nanowires Reinforced Pure Al Composite

Silicon Nitride Whisker-Reinforced Aluminum Matrix Composites: Twinning and Precipitation Behavior

Untrasonic-Assisted Fabrication of SiC Nanoparticles Reinforced Aluminum Matrix Composites

High-Si Reinforced Al Matrix Composites Prepared by Powder Semi-Solid Squeeze

Fabrication of toughened Cf/SiC whisker composites and their mechanical properties

MICROSTRUCTURE AND PROPERTIES OF DEFORMABLE SiC_P/Al COMPOSITE FABRICATED BY SQUEEZE CASTING METHOD

Enhanced Mechanical Behavior and Fabrication of Silicon Carbide Particles Covered by In-Situ Carbon Nanotube Reinforced 6061 Aluminum Matrix Composites