Abstract:Optimized shape anisotropy of the Fe-Co rich ferromagnetic (α 1 ) phase and the effective separation of the α 1 and α 2 phases with maximum magnetization difference—where α 2 represents a paramagnetic magnetic phase—are the key parameters for maximizing the magnetic properties of Alnico magnets. In this manuscript, efforts have been undertaken to optimize the shape anisotropy of the α 1 phase and increase the difference in magnetization and separation between α 1 and α 2 phases by fine tuning Al and Ni contents, directional solidification and magnetic field annealing methods. At first, Alnico magnets were fabricated by adjusting the content of α 2 phase followed by homogenization, magnetic field annealing at high temperature, and low-temperature tempering. Intrinsic coercivity ( H cj ) of ⁓146.0 kA/m, remanence ( B r ) of ⁓0.90 T and maximum energy density ( (BH) max ) of 46.02 kJ/m 3 are achieved in the magnet with 8.2 wt% Al and 12.8 wt% Ni treated in field of 1.5 T for 10 minutes. At the second stage, the magnet with optimal magnetic properties is directionally solidified to develop columnar grains, and then the α 1 phase is grown in the direction of the columnar grains by magnetic field annealing to enhance the (BH) max to 79.8 kJ/m 3 . The axial ratio of the α 1 phase increased significantly with the increase of the grain size, particularly in the directionally solidified magnets. The Curie temperature of the α 1 phase is noted near 1150 K, while the Curie temperature of the α 2 phase is below 400 K. The magnets demonstrated excellent temperature stability, with magnetic properties decreasing by only 10–12 % at 800 K. These results may pave the way for further development of Alnico magnets specifically for high temperature applications.

Magnetically Aligned Al<sub>3</sub>Ni Phase in Al-Ni Alloys Solidified with a High Magnetic Field

EBSD Study on the Effect of a Strong Axial Magnetic Field on the Microstructure and Crystallography of Al-Ni Alloys During Solidification

Microstructure Evolution of Magnetic Aligned MnBi Phase in Bi-Mn Alloys Solidified in High Static Magnetic Field

Alignment Behavior of MnBi Phase in Bi-Mn Alloy Solidified in Static Magnetic Field

Effect of a Weak Transverse Magnetic Field on the Morphology and Orientation of Directionally Solidified Al–Ni Alloys

Microstructure and magnetic field induced strain of directionally solidified ferromagnetic shape memory CoNiAl alloys

Preparation of Nb 3 Al Superconductor by Powder Metallurgy and Effect of Mechanical Alloying on the Phase Formation

Phase Transition and Magnetic-Field-Induced Strain in Textured Ni54Mn21Ga25 Polycrystalline Alloys

Preparation of Nb3al by High-Energy Ball Milling and Superconductivity

Influence of an Axial Magnetic Field on Microstructures and Alignment in Directionally Solidified Ni-based Superalloy

A Study of Microstructure and Crystal Orientation in Directionally Solidified Ni–Fe–Ga–Co Magnetic Shape Memory Alloys

Magnetic force microscopy observations of Co–Ni–Ga and Co–Ni–Al alloys with two-phase structures

Microstructure and Crystal Orientation of the Steady Growth Zone in the Directionally Solidified Ni-Fe-Ga-Co Magnetic Shape Memory Alloys

Phase Equilibria in the Co-Mn-Ni System

Structure, Phase Transformation and Magnetic Properties in Polycrystalline Ni47Mn32Ga21 Directionally Solidified Alloy

Refining Alnico 8 magnets with composition optimization of matrix phase, directional solidification and magnetic field annealing

Effect of a High Axial Magnetic Field on the Structure of Directionally Solidified Al–Si Alloys

Effect of solidification rate on microstructure and crystal orientation of ferromagnetic shape memory alloys Co–Ni–Al

STRUCTURE AND MAGNETIC CHARACTER OF NANOSTRUCTURED NiAl ALLOY SYNTHESIZED BY INERT-GAS CONDENSATION

Large Magnetoresistance in a Directionally Solidified Ni 44.5 Co 5.1 Mn 37.1 in 13.3 Magnetic Shape Memory Alloy

High-Magnetic-Field-Induced Formation of Aligned Equiaxed Grains During Directional Solidification