Analysis of Dynamic Response of Engine Crankshaft

Zhang Yangang,Zhang Baocheng

DOI: https://doi.org/10.3969/j.issn.1671-0614.2006.04.003

2006-01-01

Abstract:Taking a heavy-duty engine′s crankshaft as an example, this paper presents how to accomplish a 3D modeling, FEA meshing, modal analyzing and dynamic response calculating based on I-deas10.0 software. This method has a reference value to other mechanism′s dynamic design.

What problem does this paper attempt to address?

Force Analysis of Engine Crankshaft Based on Finite Element Method

Yun Xin Chen

DOI: https://doi.org/10.4028/www.scientific.net/amm.529.460

2014-06-01

Applied Mechanics and Materials

Abstract:In this paper, the working states of the engine crankshaft stress by detail force analysis of engine crankshaft and 3D modeling by finite element method, understanding the stresses and deformation of the engine crankshaft, improve the analysis provides a theoretical basis for structure design; has an important significance for optimization, guide the crank shaft.
Study of Automatic Dynamic Balancing System for Engine Crankshaft

CHENG Tao-tao,ZENG Sheng,LI Bin,JIN Tao

DOI: https://doi.org/10.3969/j.issn.1001-2265.2012.08.001

2012-01-01

Abstract:In order to improve the dynamic balancing efficiency,accuracy and the automation of the crankshaft for the inland manufacture,an automatic dynamic balancing scheme is studied.Form the view point of the system,the key problems that should be considered is summarized,w hich include the balancing test unit and driving system,the support-up and rotating unit,the drilling unit,the scraps disposal unit,the control system structure,the controller,the analogue and the digital signal process,the mathematic model,the cut positioning method,the sequence control method and so on.The prototype machine is developed.And the experimental results prove that the scheme is successful.
Analysis on Crankshaft System's Dynamical Behavior Based on Simulation and Experimental Methods

Zhi-yong HAO,Qiong LIN,Xiu-bing DUAN

DOI: https://doi.org/10.3969/j.issn.1000-0925.2006.01.009

2006-01-01

Abstract:A rigid and a flexible dynamical model for a diesel engine crankshaft system have been built with ADAMS. The dynamical characteristic data of the two crankshaft system obtained from model simulation are analyzed and compared respectively. Also, the experiment data are compared by simulation data, which proves the reliability of the model and gives a foundation for the coupling dynamical analyze and the optimization design of crankshaft system.
Dynamic Analysis of 4D20 Passenger Car Diesel Engine Crankshaft System

Li Xiaofeng,Yuan Zhaocheng,Zhao Fuquan,Wu Chengming

DOI: https://doi.org/10.3969/j.issn.1000-3703.2010.12.006

2010-01-01

Abstract:A crankshaft system dynamic model for a 2.0L high speed direct injection car diesel engine was established,which was used for crankshaft torsional vibration analysis,bending vibration analysis and fatigue strength analysis.The results indicated that torsional vibration and bending vibration of this crankshaft assembly complied with design requirement and no torsional resonance occurred,the maximum torsional vibration angle is lower than 0.2°,and the minimum high-frequency fatigue safety coefficient is 1.324 at the front-end single order at rated speed,this diesel engine has good dynamic property and complied with operating requirement.
Determination on the Operation Condition of Crankshaft of Diesel Engine and Its Static Strength Analysis

Shilie Zheng

2006-01-01

Abstract:Utilizing MSC.PatranNastran to carrying out 3D entity modeling on the entire crankshaft of the diesel engine,the division of meshes and the finite element analysis of static strength.Adopting the spring unit to simulate the support of main bearing so as to let the computation model be more close to the actual situation.The combination effect of bending and twisting has been considered while defining the dangerous operation condition of the crankshaft.Taking the finite element result as a base,a kind of method on determining more precisely the dangerous operation condition of the crankshaft was put forward.It is verified that the most dangerous operation condition of crankshaft is not happening at the upper point of gas re-inlet or while the crankpin is bearing a maximum force of gas.Finally,the checking-up of safety coefficient of fatigue strength was carried out on the crankshaft by means of adopting the method of equivalent stress.
Finite element analysis of a vehicle diesel engine crankshaft

Fengliang Liu,Zhongcai Zheng,WeiLuo,Dongyue Han,Yifan Zhang

DOI: https://doi.org/10.1088/1742-6596/1653/1/012042

2020-10-01

Journal of Physics: Conference Series

Abstract:Abstract The crankshaft is the largest moving part in the engine and one of the most important parts in the engine. It bears the force transmitted from the connecting rod and converts this force into torque. The working conditions of the crankshaft are harsh, and its stress conditions are quite complicated. The stress concentration phenomenon is quite serious under the effect of bending and torsion loads, especially in the rounded transition area from the crank to the journal. In addition, the crankshaft has a significant impact on the overall size, weight, reliability, and manufacturing cost of the engine Therefore, the fatigue strength, stiffness, and wear resistance of the journal must be strictly checked and analyzed during the design of the crankshaft. In this paper, the finite element method is used as the main research method to analyze the static strength of a diesel engine crankshaft. The pre-processing software is used to optimize the topology of the crankshaft 1/2 single turn and the tetrahedral meshing. Then the finite element analysis software is imported to set the boundary Condition and apply the load, and finally submit the calculation. According to the working conditions, the crank pin load and the main journal support reaction force are calculated. Through the analysis of the results of crankshaft statics simulation, the weak links of the stress distribution of the crankshaft under dangerous conditions are found, which provides a theoretical basis for the structural design of the crankshaft.
Force and Motion Analysis of Crankshaft and Mainshaft of a Diesel Engine

HU Hua-zhong,Ltd N

2012-01-01

Abstract:Strengthen analysis was conducted on a medium-speed,V16 diesel engine adopting ANSYS software,and different stress status of crankshaft with ignition in different pneumatic cylinders were obtained.Then re-calcultion and reexamination to the strength was conducted by AVL-Designer.Additionally,the working conditions of mainshaft bearings were calculated in order to facilitate analysis of its force,axial center track and lubricating condition.
AN EFFICIENT CRANKSHAFT DYNAMIC ANALYSIS USING SUBSTRUCTURING WITH RITZ VECTORS

Z.P. MOURELATOS

DOI: https://doi.org/10.1006/jsvi.2000.3208

IF: 4.7

2000-11-01

Journal of Sound and Vibration

Abstract:A structural analysis using dynamic substructuring with Ritz vectors is presented for predicting the dynamic response of an engine crankshaft, based on the finite-element method. A two-level dynamic substructuring is performed using a set of load-dependent Ritz vectors. The rotating crankshaft is properly coupled with the non-rotating, compliant engine block. The block compliance is represented by a distributed linear elastic foundation at each main bearing location. The stiffness of the elastic foundation can be different in the vertical and horizontal planes, thereby considering the anisotropy of the engine block compliance with respect to the crankshaft rotation. The analysis accounts for the kinematic non-linearity resulting from the crankangle-dependent circumferential contact location between each journal and the corresponding bore of the engine block. Crankshaft “bent” and block “misboring” effects due to manufacturing imperfections are considered in the analysis. The superior accuracy and reduced computational effort of the present method as compared with the equivalent superelement analysis in MSC/NASTRAN, are demonstrated using the free and forced vibrations of a slender cylindrical beam and free vibrations of a four-cylinder engine crankshaft. Subsequently, the accuracy of the present method in calculating the dynamic response of engine crankshafts is shown through comparisons between the analytical predictions and experimental results for the torsional vibrations of an in-line five cylinder engine and the bending vibrations of the crankshaft-flywheel assembly of a V6 engine.

engineering, mechanical,mechanics,acoustics
Torsional Vibration Analysis Based on Multi-body Dynamics of Flexible Crankshaft System

Xing-yu LIANG,Ge-qun SHU,Dong-hai LI,Ying-gang SHEN

DOI: https://doi.org/10.3969/j.issn.1000-0925.2007.04.012

2007-01-01

Abstract:Based on the FEA model of crankshaft system,a dynamic system consisting of both the flexible bodies and the rigid bodies was established by using the multi-body dynamics analysis.Through torsional response analysis by this model,the time history which was used as evaluation of power characteristics and safety was calculated in detail.Then with a newly designed testing set-up,the torsional vibration of the crankshaft of a 4-cylinder diesel engine was measured at the free-end.The comparison of the calculated and measured results show that the calculated values of the main order are in better agreement with the measured values,and the validity of the model is proved.
Dynamic simulation research on diesel engine's cranktrain and block

Lei GUO,Zhi-yong HAO,Qiong LIN

DOI: https://doi.org/10.3785/j.issn.1008-973X.2007.05.016

2007-01-01

Abstract:By using the modal synthesis technique of finite element method (FEM), the components such as the engine block and crankshaft were reduced to flexible bodys for dynamics analysis. The coupled system of the engine cranktrain and block was set up in ADAMS. The Reynold's equation was used to describe the hydrodynamics characteristic of the mainbearing's lubrication oil-film. From the dynamics simulation results, the boundary conditions of the NVH (noise, vibration and harshness) characteristics such as the piston thrust, the mainbearing's load and the minimum oil-film thickness etc. were obtained. After getting the orbits of the main-journal center, the differences between the engine block building with the flexible body and the rigid body were compared. Consequently, using the test data of the engine block surface's vibration validated the results of the coupled system dynamics simulation.
Dynamic Analysis of the Crank and Connecting Rod of Single-Cylinder Gasoline Engine Before and After Adjustment

Wang Shangli,Pei Pucheng,Chen Guangyu,Lai Xiaoli

2012-01-01

Abstract:Three-dimensional solid of crank and connecting rod are built with CATIA,mesh pretreatment with HYPERMESH.The parameters of crank-connecting rod mechanism,the working fluid pressure in the cylinder and load conditions are taken as input,dynamic analysis on the crankshaft before and after adjustment with AVL-EXCITE is carried out to identify the differences between the two points.The results show that: Speed fluctuation rate,axial torsion angle and the overall amplitude of the unbalanced force of crank adjusted decrease,the right crankshaft journal bearing capacity of crank adjusted increases.Crankshaft adjusted has been used in products,helping to improve the vibration and reduce degree of wear of the connecting rod big end.
Multi-body dynamics and finite element method co-simulation for crankshaft dynamical strength analysis

GUO Lei,HAO Zhi-yong,LIU Bo,YU Bo

DOI: https://doi.org/10.3785/j.issn.1008-973X.2009.09.016

2009-01-01

Abstract:The cranktrain and cylinder assemble multi-body dynamics model using the stiffness and mass matrix were established with Excite powered by AVL.The each journal orbits and oil film pressure were obtained considering the elastic hydro dynamic bearing characteristics.The global finite element model was calculated by using the finite element analysis(FEA) submodel method.Then the critical pin fillet of the last crankweb was driven by the crankweb's global model for calculating the stress history in an engine cycle.The dynamic fatigue safety factor of the critical fillet was obtained by using the strain-life fatigue model and fatigue strength comparison factor was evaluated with component design standard.The simulation results of the crankshaft modal parameters and the torsion vibration in running condition were compared by the experimental results.The method for crankshaft dynamics fatigue analysis showed good accuracy and efficiency.
Failure Analysis of a Diesel Engine Crankshaft based on Finite Element Modeling

Eiman Solangi,Imdad Ali Memon,Munwar Ayaz Memon,Muhammad Raees,Mohammad Atif Khan

DOI: https://doi.org/10.55447/jaet.07.01.82

2023-06-30

Journal of Applied Engineering & Technology (JAET)

Abstract:The crankshaft is one of the essential components of an internal combustion engine that converts the piston's linear motion into the crank's rotary motion. This research has been carried out to study the failure analysis of diesel engine crankshafts, and forged steel material is selected. A crankshaft's geometry is relatively complex compared to other parts; its working conditions are critical, and the stress concentration areas are very complicated. While considering all these phenomena, it is significant that a crankshaft's fatigue strength, stiffness, durability, and wear resistance should be checked and analyzed properly. Firstly, a 3D model of the crankshaft is designed using SolidWorks 2022 software. After that, the Model is imported to ANSYS software 2022 R2 student version. However, using ANSYS (finite element method) is carried out on the crankshaft’s Model. This research aims to obtain the variation in stress magnitude at critical locations of the crankshaft by applying variable loads and boundary conditions. Simulation techniques were conducted for both static and dynamic analysis. The total deformation observed at the critical area of the crank pin is 1.3488e-8. The corresponding equivalent stress is 318.37, and the crankshaft's safety factor is 15.
Finite element analysis for the crankshaft of the piston compressor

Bin Zhao

DOI: https://doi.org/10.4028/www.scientific.net/AMR.102-104.17

2010-01-01

Abstract:In order to study the static and dynamical characteristics of the crankshaft, ANSYS software was used to carry out the corresponding calculations. The entity model of the crankshaft was established by UG software firstly, and then was imported into ANSYS software for meshing, and then the finite element model of the crankshaft was constructed. The crankshaft satisfied the requirement of stiffness and strength through static analysis. The top six natural frequencies and corresponding shapes were acquired through modal analysis, and the every order critical rotating speed of the crankshaft was calculated. The fatigue life of the crank was calculated by fatigue module of ANSYS software finally. These results offered the theoretical guidance for designing, manufacturing and repairing the crankshaft.
Engine Multi-Body with Flexible Crankshaft Modeling and Numerical Simulation

Ming Liu,Yonghong,Hong Wang,Hong Li,Xianfeng Gu,Hongliang,Bo Zhang,Youyun

2005-01-01

Abstract:A multi-body model of engine system with flexible crankshaft was presented in this paper to analyze the dynamic behavior of an internal combustion engine. The flexible crankshaft structural dynamics was coupled with the main bearing hydrodynamic lubrication in this model by a system approach. An application of an I4 engine was given to show this sophisticated simulation model and to predict the loads and the orbit plots in the journal bearings by the dynamic response of the multi-body engine system with flexible crankshaft. The numerical results show the capabilities and significance of the flexible crankshaft in this system. The objective of the research is to provide the scientific guidance for design and maintenance of the internal combustion engine.
On Finite Element Analysis and Optimum Design of Crankshaft

HUANG Zhen,ZHANG JI-chun

DOI: https://doi.org/10.3969/j.issn.1007-855x.2006.04.023

2006-01-01

Abstract:In order to further research dynamic characteristics of crankshaft under real circumstance,the multi-body dynamics model of engine crank gear is first set up.Based on the results from the multi-body dynamics analysis,the finite element analysis of crankshaft is accomplished,and then how the transition fillet influence on the maximum stress is analyzed.At last a one-cylinder crankshaft model is used to optimize the best crankshaft transition fillet.An exploration is made into the basic method to optimize design crankshaft using modern design tools.
Simplified model for vibration analysis of diesel engine crankshaft system

Xuan Yang Lei,ZHANG Gui-cai,Jin Chen,SONG Xi-geng,DONG Guang-ming,雷宣扬,张桂才,陈进,宋希庚,董广明

2006-01-01

Journal of Shanghai Jiaotong University (Science)

Abstract:A spatial finite element model for vibration analysis of crankshaft system was proposed. The crankshaft body was simplified as spatial rigid frame by using beam elements based on Timoshenko beam theory. The main bearings in system were simplified as linear springs and dashpots. The natural frequencies of the crankshaft system of a four in-line cylinder engine were calculated and compared with the analytical and experimental values available in other publications. In order to simulate the motion of operating crankshaft system, the gas forces, rotating masses and reciprocating masses were considered, the crankshaft and main bearings were coupled in a rotating coordinate system, and a dynamic model for vibration analysis of crankshaft system was established. By applying the dynamic model, the influence of the mass and moment of inertia of front pulley on the behavior of crankshaft vibration was investigated.
Modeling on the Dynamics of Crankshaft with Crack in Fillet Region

Xuan-yang LEI,Gui-cai ZHANG,Jin CHEN,Xi-geng SONG,Guang-ming DONG

DOI: https://doi.org/10.16183/j.cnki.jsjtu.2006.08.003

2006-01-01

Shanghai Jiaotong Daxue Xuebao/Journal of Shanghai Jiaotong University

Abstract:A model for modeling and analyzing the dynamics of cracked crankshaft was developed, and the nonlinear vibrations of the cracked crankshaft were simulated and analyzed. A crankshaft with a frequent crack in crankpin-web fillet region was investigated, and a finite element model based on combination of Timoshenko beam element and cracked bean element was proposed. The breathing behavior of the crack and the motion characteristic of crankshaft under operating condition were studied, and a model of nonlinear motion was established in a rotating coordinate system. A crankshaft of four in-line cylinder engine was applied as an example, and the vibration response of crankshafts with different depth crack was simulated. The study indicates that the model proposed for cracked crankshaft is compact and effective; the analysis on dynamics of cracked crankshaft lays a theoretical foundation for the diagnosis on crack fault of crankshaft.
Modeling and Analyzing of Vibration in Working Crankshaft with Cracks

Xuan Yang Lei,Gui Cai Zhang,Xi Geng Song,Jin Chen,Guangming Dong

DOI: https://doi.org/10.4028/www.scientific.net/KEM.293-294.401

2005-01-01

Key Engineering Materials

Abstract:In this paper, a simplified finite element model of the cracked crankshaft is proposed, and a new method for simulating the nonlinear vibration of operating crankshaft with several cracks is presented. For crankshaft, cracks occur frequently in the parts of crankpin-web fillet region and the edge of oil aperture because of fatigue or damage. According to the characteristic of those cracks, the cracked parts are modeled by the corresponding cracked spatial finite elements respectively, and two cracked elements are discussed in this study. The other, un-cracked, crankshaft parts are modeled by spatial Timoshenko beam elements. Flywheel and front pulley are simplified as lumped mass elements, and main bearings are simulated by equivalent linear springs and dashpots. In order to find the dynamic response of crankshaft-bearing system, a right-handed rotating coordinate system attached to crankshaft is applied. Based on the proposed finite element model, the breathing behavior of cracks in operating crankshaft is studied, and the nonlinear motion equation with variational stiffness is formed. Finally, a four-in-line crankshaft is taken as an example, and its vibration response corresponding to different kinds of crack are calculated and analyzed. Some conclusions are drawn, and a foundation is laid for diagnosing crack fault of crankshaft.
Finite Element Analysis of Marine Diesel Engine Crankshaft

Bin Zheng,Yongqi Liu,Ruixiang Liu,Jian Meng

DOI: https://doi.org/10.1007/978-3-642-23777-5_110

2011-01-01

Abstract:In this paper, with the ANSYS, stress distribution and safety factor of crankshaft were analyzed by using 3D finite element method. The results show that the exposed destructive position is the transition circular bead location of the crank web and the crankpin. Maximum stress is 112.8 MPa. Safety factor is 3.32. Crankshaft satisfies the design requirement.

Analysis of Dynamic Response of Engine Crankshaft

Force Analysis of Engine Crankshaft Based on Finite Element Method

Study of Automatic Dynamic Balancing System for Engine Crankshaft

Analysis on Crankshaft System's Dynamical Behavior Based on Simulation and Experimental Methods

Dynamic Analysis of 4D20 Passenger Car Diesel Engine Crankshaft System

Determination on the Operation Condition of Crankshaft of Diesel Engine and Its Static Strength Analysis

Finite element analysis of a vehicle diesel engine crankshaft

Force and Motion Analysis of Crankshaft and Mainshaft of a Diesel Engine

AN EFFICIENT CRANKSHAFT DYNAMIC ANALYSIS USING SUBSTRUCTURING WITH RITZ VECTORS

Torsional Vibration Analysis Based on Multi-body Dynamics of Flexible Crankshaft System

Dynamic simulation research on diesel engine's cranktrain and block

Dynamic Analysis of the Crank and Connecting Rod of Single-Cylinder Gasoline Engine Before and After Adjustment

Multi-body dynamics and finite element method co-simulation for crankshaft dynamical strength analysis

Failure Analysis of a Diesel Engine Crankshaft based on Finite Element Modeling

Finite element analysis for the crankshaft of the piston compressor

Engine Multi-Body with Flexible Crankshaft Modeling and Numerical Simulation

On Finite Element Analysis and Optimum Design of Crankshaft

Simplified model for vibration analysis of diesel engine crankshaft system

Modeling on the Dynamics of Crankshaft with Crack in Fillet Region

Modeling and Analyzing of Vibration in Working Crankshaft with Cracks

Finite Element Analysis of Marine Diesel Engine Crankshaft