Abstract:This paper investigates the effect of wet-blasting pressure on the surface integrity and tool cutting performance of hybrid CVD-TiN/TiCN/α-Al2O3/TiN coated tools. The hybrid TiN/MT-TiCN/α-Al2O3/TiN multilayer coating was deposited on the cemented carbide inserts’ surface by chemical vapor deposition (CVD) technique. Then the coated inserts were subjected to wet-blasting by aluminum oxide with varying pressure. The coatings were characterized by scanning electron microscopy, white light surface profiler, and X-ray residual stress diffractometer. The results indicate that the average residual tensile stress of the α-Al2O3 layer on the rake face of CVD-coated inserts gradually decreased with the increase of wet-blasting pressure. When the wet-blasting pressure reached 0.24 MPa, the residual tensile stress was transformed into compressive stress. It was accompanied by increased cutting edge roughness and cutting edge radius, reduced cutting edge coating thickness, and a change in rake face surface roughness. To understand the effect of the surface integrity change on the cutting performance of CVD-coated inserts, a case study designed for AISI 4340 steel machining under continuous and intermittent cutting conditions is performed. When the Al2O3 layer on the cutting edge is not peeled off by wet-blasting, the change of residual stress from tensile to compressive in the rake face of CVD-coated inserts can effectively improve the fracture failure resistance of inserts in continuous and intermittent cutting processes. When the Al2O3 layer on the cutting edge is not peeled off by wet-blasting, the fracture failure resistance during intermittent cutting will be significantly reduced.

Preparation and Cutting Performanle of ZrN/TiN Coated Tool

Development of ZrN/TiN Coated Tool and Study on Its Wear Performance

HARD AND WEAR-RESISTANT TITANIUM NITRIDE COATINGS DEPOSITED BY PULSED HIGH ENERGY DENSITY PLASMA FOR CUTTING TOOLS

Study on the preparation of hard and wear-resistant titanium nitride films on silicon nitride ceramic cutting tools

Microstructure and Mechanical Properties of Titanium Nitride Coatings for Cemented Carbide Cutting Tools by Pulsed High Energy Density Plasma

Mechanics and Cutting Performance of Multilayer Nanostructured TiAlN/TiSiN/ZrN Coatings

Performance of PVD MoS2/Zr-coated Carbide in Cutting Processes

Wear‐Resistant Titanium Carbonitride Coatings Onto WC–Co Cutting Tools by Pulsed High‐Energy Density Plasma

Cutting performance and wear mechanism of multilayer diamond coated tools

Cutting Performance of TiN/TiSiN Coated Tool during Turning of Ti6Al4V Titanium Alloy

Properties and Performance of TiAlSiN and AlCrN Monolayer and Multilayer Coatings for Turning Ti-6Al-4V

Influence of different wet-blasting pressure on the surface integrity and tool cutting performance of hybrid CVD-TiN/TiCN/α-Al2O3/TiN coated tools

Structure of the Coatings Onto Ceramic Cutting Tools Deposited by Pulsed High Energy Density Plasma

Comparative analysis over microstructural, mechanical properties and cutting performance of TiN, TiVN coatings deposited by magnetron sputtering on SiAlON ceramic tool insert

Investigations on microstructure, mechanical and tribological properties of TiN coatings deposited on three different tool materials

Machining Performance of Sputter-Deposited (al0.34cr0.22nb0.11si0.11ti0.22)50n50 High-Entropy Nitride Coatings

Microstructure and Properties of the AlCrSi(O)N Tool Coatings by Arc Ion Plating

Nanometer Grain Titanium Carbonitride Coatings with Continuously Graded Interface Onto Silicon Nitride Cutting Tools by Pulsed High Energy Density Plasma

Tribological Characteristics of TiN and TiCN Hard Coatings Prepared by Pulsed D.C. Plasma Enhanced Chemical Vapour Deposition

Preparation and Cutting Performance of Nanoscaled Al2O3-coated Micro-Textured Cutting Tool Prepared by Atomic Layer Deposition

Adhesive wear mechanism of coated tools and its influence on cutting performance during machining of Zr-based bulk metallic glass