Abstract:Finding a wear resistant coating for cemented carbide cutting tools in the machining of difficult to cut Ti alloys is a challenge due to their high strength and chemical reactivity. Tool manufacturers recommend physical vapor deposited (PVD) TixAl1-xN (x = 0.4–0.7), and an extra NbN overlayer has shown promising potential. This study explores wear mechanisms of PVD Ti0.45Al0.55N with and without NbN overlayer and its WC-Co substrate in machining Ti alloys. To achieve an accurate understanding of tool-chip-workpiece interaction and related wear mechanisms, several approaches were employed. Tests with controlled variation of cutting speeds were complemented by process freezing experiments using the quick stop method and imitational experiments of diffusion couples. Advanced microscopy techniques were employed for accurate detection of wear products and phenomena across length scale. Findings reveal that any new design of coatings for Ti machining must combine both high mechanical integrity and resistance to diffusional dissolution and oxidation. Observed diffusional loss of Al and N from the coating results in a TiN layer which is mechanically weaker than the original coating, while the NbN overlayer reduces the Al diffusion rate, but NbN is subjected to diffusional dissolution itself. On dissolution, Nb stabilizes β-Ti and thus facilitating loss of Al, but the observed formation of intermetallic Nb3Al at the NbN–Ti interface works as a diffusion barrier. However, brittle Nb3Al can be more easily removed during machining. It was found that the coating retains longest on the edge line and protects the tool edge from failure because substrate cemented carbide wears at a faster rate than the coating with outward diffusion of C from WC grains and Co binder.

Development of ZrN/TiN Coated Tool and Study on Its Wear Performance

Preparation and Cutting Performanle of ZrN/TiN Coated Tool

HARD AND WEAR-RESISTANT TITANIUM NITRIDE COATINGS DEPOSITED BY PULSED HIGH ENERGY DENSITY PLASMA FOR CUTTING TOOLS

Study on the preparation of hard and wear-resistant titanium nitride films on silicon nitride ceramic cutting tools

Wear‐Resistant Titanium Carbonitride Coatings Onto WC–Co Cutting Tools by Pulsed High‐Energy Density Plasma

Microstructure and Mechanical Properties of Titanium Nitride Coatings for Cemented Carbide Cutting Tools by Pulsed High Energy Density Plasma

Investigations on microstructure, mechanical and tribological properties of TiN coatings deposited on three different tool materials

Mechanics and Cutting Performance of Multilayer Nanostructured TiAlN/TiSiN/ZrN Coatings

Microstructure and Properties of the AlCrSi(O)N Tool Coatings by Arc Ion Plating

Wear-resistant ZrN/Ti functionally graded coating prepared on TA18 alloy by double glow plasma alloying

Nanometer Grain Titanium Carbonitride Coatings with Continuously Graded Interface Onto Silicon Nitride Cutting Tools by Pulsed High Energy Density Plasma

Structure of the Coatings Onto Ceramic Cutting Tools Deposited by Pulsed High Energy Density Plasma

Performance of PVD MoS2/Zr-coated Carbide in Cutting Processes

Tribological Characteristics of TiN and TiCN Hard Coatings Prepared by Pulsed D.C. Plasma Enhanced Chemical Vapour Deposition

Comparative analysis over microstructural, mechanical properties and cutting performance of TiN, TiVN coatings deposited by magnetron sputtering on SiAlON ceramic tool insert

TiC nano-coating and their tribological properties were deposited by doal-ion beam sputtering on the tool surface

Machining Performance of Sputter-Deposited (al0.34cr0.22nb0.11si0.11ti0.22)50n50 High-Entropy Nitride Coatings

Properties and Performance of TiAlSiN and AlCrN Monolayer and Multilayer Coatings for Turning Ti-6Al-4V

Influence of different wet-blasting pressure on the surface integrity and tool cutting performance of hybrid CVD-TiN/TiCN/α-Al2O3/TiN coated tools

On wear of TiAlN coated tools with and without NbN overlayer in machining titanium alloys

Effect of Al Content on the Wear Evolution of Ti1-xAlxN-Coated Tools Milling Ti-6Al-4V Alloy