Abstract:The use of carbon nanotubes (CNTs) as the reinforcing phase to prepare copper-based composite materials can improve the strength and high conductivity of copper-based conductors. In order to analyze the effect of surface oxidation modification on the structural properties of carbon nanotubes and its strengthening effect on composite materials, this article combines heterogeneous copolymerization liquid phase mixing method and spark plasma sintering molding method; prepares the carbon nanotubes/copper composite materials using carbon nanotubes under different oxidation treatment conditions as the reinforcing phase (the volume fraction of carbon nanotubes is 3%); and characterizes the microstructure, mechanical properties, and electrical and thermal conductivity of the composite material. Studies have shown that the tensile strength and hardness of composite materials first increase with the increase of CNT oxidation treatment time and then decrease with the increase of oxidation treatment time. When the oxidation treatment time is 4 h, CNTs are uniformly dispersed in the matrix while maintaining good structural integrity and load-bearing capacity, and the composite material has the highest mechanical properties. The tensile strength of the composite material made of 80‐ nm CNTs reaches 452.4 MPa, which is 1.6 times that of pure copper, and the hardness reaches 127.4HV, which is twice that of pure copper. The electrical conductivity and thermal conductivity of the composite material first increase with the increase of the oxidation treatment time of carbon nanotubes and then decrease with the increase of the oxidation treatment time. The 80 nm CNT reinforced composite material has better CNT dispersion performance and higher conductivity than that of 15 nm CNT preparation. The electrical conductivity of the composite material reaches the maximum value of 92% IACS when the CNT oxidation treatment time is 4 hours, which is 95% of the pure copper sample, and the electrical conductivity is significantly better than that of the CNT/Cu composite material and copper alloy prepared by other methods. The thermal conductivity of composite materials is lower than that of pure copper. The thermal conductivity of carbon nanotubes with an oxidation treatment time of 2 h decreases most obviously, indicating that the thermal resistance generated by the interface and agglomeration phases in the composite material affects its thermal conductivity.

A Comparative Research on Auxiliary Processes for Copper Based Carbon Nanotube Composite Electroplating

Nanoparticle Reinforced Metal Composites Prepared by Electrocodeposition

Influence on (Ni-P) Electroless Composite Plating with Carbon Nanotubes

Preparation of Cu-based composite materialsreinforced by nanotube by powder-metallurgy

Single-walled Carbon Nanotube-Reinforced Copper Composite Coatings Prepared by Electrodeposition under Ultrasonic Field

Study on new process of electroless copper plating pretreatment on carbon fiber surface

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Progress and Current Status in Research on Nanostructured Cu-Ag Microcomposites for Conductor Wires

Effective method to disperse and incorporate Carbon nanotubes in electroless Ni-P deposits

Electroless plating of copper on carbon fiber surfaces and corresponding mechanism

Influence of Carbon Nanotube Coatings on Carbon Fiber by Ultrasonically Assisted Electrophoretic Deposition on Its Composite Interfacial Property.

Investigation of the mechanical behavior of the carbon nanotubes coated copper composite materials

Preparation method of carbon nano tube enhanced copper-based composite material

Surface coarsening of carbon fiber/cyanate ester composite for adhesion improvement of electroless copper plating as conductive patterns

Electrochemical co-deposition of carbon nanotube/Ni composite layer

In Situ Study of Copper Electrodeposition on A Single Carbon Fiber

Preparation method of carbon nanotube-silicon composite cathode material

Progress of CNTs Reinforced Copper-based Composite Preparation

Recent Advances in Metal/Alloy Nano Coatings for Carbon Nanotubes Based on Electroless Plating

Effect of Surface Modification of Carbon Nanotubes on the Properties of High-Strength and High-Conductivity Copper Matrix Composites

Characterization of electrochemical deposition of copper and copper(I) oxide on the carbon nanotubes coated stainless steel substrates