Abstract:In the present work, a novel poly(arylene ether ketone) with a unique molecular design that included concentrated flexible sulfoalkyl groups and a silane cross-linked network (C-SPAEK) was prepared and used as a PEM for DMFCs. The chemical structures, sulfonation degree and phase-separated morphology were characterized and identified by 1 H NMR, FT-IR and SAXS. The resulting copolymers exhibited excellent thermal stability (T 5% >263.8 °C) and mechanical properties (tensile strength>52.88 MPa). Additionally, the high IEC values and obvious hydrophilic/hydrophobic phase-separated structure (d > 2.71 nm) ensured that the C-SPAEK membranes possessed high proton conductivities . The C-SPAEK PEMs also displayed enhanced methanol resistance and dimensional stability, which were much better than those of a recast Nafion membrane under the same conditions. The C-SPAEK-0.4 membrane maintained a low methanol absorption of less than 48.7%, even in 4 M methanol solution. In particular, the C-SPAEK-0.6 membrane exhibited the best comprehensive performance, with a high proton conductivity (0.164 S cm −1 ), low methanol uptake (52.1%) and permeability (3.63 × 10 −7 cm 2 s −1 ), and maximum power density (83.2 mW cm −2 ), when immersed in 2 M methanol at 80 °C in a DMFC single-cell. These results suggested that the C-SPAEK membranes were sufficiently tough and had the potential to overcome the problems caused by the high methanol permeability of PEMs. The unique molecular design of C-SPAEK guaranteed a rare combination of high proton conductivity and enhanced methanol resistance, which are the key determining factors for DMFC applications.

Modification of ultrathin polyetheretherketone film for application in direct methanol fuel cells

PEMs with High Proton Conductivity and Excellent Methanol Resistance Based on Sulfonated Poly (aryl Ether Ketone Sulfone) Containing Comb-Shaped Structures for DMFCs Applications

Mechanically Robust and Highly Methanol-Resistant Sulfonated Poly(ether Ether Ketone)/poly(vinylidene Fluoride) Nanofiber Composite Membranes for Direct Methanol Fuel Cells

Modified sulfonated poly(phthalazinone ether ketone) membranes with inorganic particles for potential applications in PEMFCs

Grafted polymer electrolyte membrane for direct methanol fuel cells

Preparation and DMFC performance of a sulfophenylated poly(arylene ether ketone) polymer electrolyte membrane

Design of a stable and methanol resistant membrane with cross-linked multilayered polyelectrolyte complexes for direct methanol fuel cells

Structural optimization and performance trade-off strategies for semi-crystalline sulfonated poly(arylene ether ketone) membranes in high-concentration direct methanol fuel cells

Modification of sulfonated poly (etherether ketone) composite polymer electrolyte membranes with 2D molybdenum disulfide nanosheet-coated carbon nanotubes for direct methanol fuel cell application

Sulfonated poly (ether ether ketone)/MOF hybrid polymer electrolyte membrane with ultra‐low methanol permeability for enhanced direct methanol fuel cell performance

Preparation and characterization of chemically stable polymer electrolyte membranes by radiation-induced graft copolymerization of four monomers into ETFE films

Characterization of Polyethylene-Graft-Sulfonated Polyarylsulfone Proton Exchange Membranes for Direct Methanol Fuel Cell Applications

PA-doped nanofiber composite proton exchange membranes with ultrahigh proton conductivity and methanol barrier performance for direct methanol fuel cells

Cross-linked Hydroxide Conductive Membranes with Side Chains for Direct Methanol Fuel Cell Applications

Silane cross-linked network and concentrated flexible sulfoalkyl groups for forming a novel C-SPAEK membrane with enhanced methanol resistance and proton conductivity for DMFC applications

Tröger's base polymer blended with poly(ether ketone cardo) for high temperature proton exchange membrane fuel cell applications

Sulfonated Poly(ether Ether Ketone)/polybenzimidazole Oligomer/epoxy Resin Composite Membranes in Situ Polymerization for Direct Methanol Fuel Cell Usages

Imidazolium-Functionalized Poly(Ether Ether Ketone) As Membrane and Electrode Ionomer for Low-Temperature Alkaline Membrane Direct Methanol Fuel Cell

Enhanced performance of a direct methanol alkaline fuel cell (DMAFC) using a polyvinyl alcohol/fumed silica/KOH electrolyte

Modifications on Promoting the Proton Conductivity of Polybenzimidazole-Based Polymer Electrolyte Membranes in Fuel Cells

Tetramethyl poly(aryl ether ketone) modified by DABCO cationic polymer for high temperature proton exchange membrane fuel cells