Abstract:In this paper, deoxyribonucleic acid (DNA) was employed to construct a functional film on the PDMS microfluidic channel surface and apply to perform electrophoresis coupled with electrochemical detection. The functional film was formed by sequentially immobilizing chitosan and DNA to the PDMS microfluidic channel surface using the layer-by-layer assembly. The polysaccharide backbone of chitosan can be strongly adsorbed onto the hydrophobic PDMS surface through electrostatic interaction in the acidic media, meanwhile, chitosan contains one protonatable functional moiety resulting in a strong electrostatic interactions between the surface amine group of chitosan and the charged phosphate backbone of DNA at low pH, which generates a hydrophilic microchannel surface and reveals perfect resistance to nonspecific adsorption of analytes. Aminophenol isomers (p-, o-, and m-aminophenol) served as a separation model to evaluate the effect of the functional PDMS microfluidic chips. The results clearly showed that these analytes were efficiently separated within 60s in a 3.7 cm long separation channel and successfully detected on the modified microchip coupled with in-channel amperometric detection mode at a single carbon fiber electrode. The theoretical plate numbers were 74,021, 92,658 and 60,552 Nm(-1) at the separation voltage of 900 V with the detection limits of 1.6, 4.7 and 2.5 microM (S/N=3) for p-, o-, and m-aminophenol, respectively. In addition, this report offered an effective means for preparing hydrophilic and biocompatible PDMS microchannel surface, which would facilitate the use of microfluidic devices for more widespread applications.

Improvement of heat dissipation for polydimethylsiloxane microchip electrophoresis.

Poly(dimethylsiloxane) Microchips with Two Sharpened Stretching Tips and Its Application to Protein Separation Using Dynamic Coating

Elimination of suction effect in interfacing microchip electrophoresis with inductively coupled plasma mass spectrometry using porous monolithic plugs.

A Rigid Poly(dimethylsiloxane) Sandwich Electrophoresis Microchip Based on Thin‐casting Method

Ultraviolet Sealing and Poly(dimethylacrylamide) Modification for Poly(dimethylsiloxane)/glass Microchips

Experimental Study on the Hot Embossing Polymer Microfluidic Chip

Design and Numerical Analysis of A Joule-Heating-Induced Continuous-Flow Polymerase Chain Reaction Microchip

Deoxyribonucleic Acid Modified Poly(dimethylsiloxane) Microfluidic Channels for the Enhancement of Microchip Electrophoresis

Two Benches PDMS Free Flow Electrophoresis Chip

Design and Experiment of a PDMS-based PCR Chip with Reusable Heater of Optimized Electrode

Research on Heat Transfer for Hot Embossing of Polymeric Microfluidic Chips

Fabrication Method Based On Marginal Reinforcing And Improved High-Voltage Contactless Conductivity Detector For Poly(Dimethylsiloxane)/Glass Microchips

An Integrated Pdms Electrophoresis Microchip with Led Induced Fluorescence Detection

Thermal modeling of PMMA microfluidic separation chips

A New High-Speed Excimer Laser Micromachining Method for PMMA Based Capillary Electrophoresis Chip

Simulation and experiment of separation efficiency affected by Joule Heat on electrophoresis chip

Gel Electrophoresis Chip Using Joule Heat Self-Dissipation, Short Run Time, and Online Dynamic Imaging

A Sol-Gel-Modified Poly(Methyl Methacrylate) Electrophoresis Microchip with A Hydrophilic Channel Wall

Study on a Low Power and High Efficiency Micro Heater Used in Μpcr Chip

Polydimethylsiloxane microfluidic chip with integrated microheater and thermal sensor.

High-Throughput Continuous-Flow Separation in a Micro Free-Flow Electrophoresis Glass Chip Based on Laser Microfabrication