Abstract:Amorphous poly(ethylene terephthalate) (PET), which possess a low softening temperature (Ts=75°C), was exploited to fabricate the electrophoresis chip with an integrated gold electrode for amperometric detection, with emphases being focused on the PET surface modification via UV light and air plasma. Both UV irradiation and plasma treatment were found to be able to improve the surface wettability, enhance the supported electroosmotic flow (EOF), and increase thermal bonding strength of PET sheets, with the latter being more efficient and less time-consuming than the former in the surface modification. Upon treated with plasma for 2min, the PET sheets could be thermally bonded at 65°C. T-peer test showed that the bonding strength increased from 10g/cm for native PET sheets to 1250g/cm for the plasma treated sheets when chips were bonded at the softening point, Attenuated-total-internal-reflection spectrum showed that, after being exposed to the UV light, carboxylic groups site-selectively formed in the UV-exposed region on PET surface. These UV-induced carboxylic groups were further utilized as the scaffold for preparation of micro-gold electrode via electroless gold plating. By using this established UV-directed electroless plating and the plasma-assisted thermal bonding techniques, the full PET electrophoresis chip with an integrated micro-gold electrode could be fabricated in common chemistry laboratory without the need of clean rooms. The fabricated PET chips were demonstrated for separation and detection of model analytes of dopamine (DA) and catechol (CA). Satisfactory resolution of the two analytes was achieved within 40s, and detection limits of 0.87μM and 1.28μM for DA and CA were obtained, respectively.

A Sol-Gel-Modified Poly(Methyl Methacrylate) Electrophoresis Microchip with A Hydrophilic Channel Wall

Electrophoresis Microchips with Sharp Inlet Tips, for Contactless Conductivity Detection, Fabricated by In-Situ Surface Polymerization

Fabrication and Performance of Poly(methyl Methacrylate) Microfluidic Chips with Fiber Cores.

Low-cost Fabrication of Poly(methyl Methacrylate) Microchips Using Disposable Gelatin Gel Templates.

Fabrication of poly(methyl methacrylate) capillary electrophoresis microchips by in situ surface polymerization.

Poly(methyl Methacrylate) CE Microchips Replicated from Poly(dimethylsiloxane) Templates for the Determination of Cations

Proteins Modification of Poly(dimethylsiloxane) Microfluidic Channels for the Enhanced Microchip Electrophoresis.

Hydrophilic Biopolymer Grafted on Poly(dimethylsiloxane) Surface for Microchip Electrophoresis.

Fabrication of Poly(dimethylsiloxane)-Based Capillary Electrophoresis Microchips Using Epoxy Templates

A New High-Speed Excimer Laser Micromachining Method for PMMA Based Capillary Electrophoresis Chip

Covalent modified hydrophilic polymer brushes onto poly(dimethylsiloxane) microchannel surface for electrophoresis separation of amino acids

Fabrication and performance of fiber electrophoresis microchips.

Modification of Amorphous Poly(ethylene Terephthalate) Surface by UV Light and Plasma for Fabrication of an Electrophoresis Chip with an Integrated Gold Microelectrode

Phase-changing sacrificial materials for solvent bonding of high-performance polymeric capillary electrophoresis microchips

In-Situ Grafting Hydrophilic Polymer on Chitosan Modified Poly (dimethylsiloxane) Microchip for Separation of Biomolecules

Modification of Poly(dimethylsiloxane) Microfluidic Channels with Silica Nanoparticles Based on Layer-by-layer Assembly Technique

Solvent Bonding of Poly(methyl Methacrylate) Microfluidic Chip Using Phase‐changing Agar Hydrogel As a Sacrificial Layer

Deposition of PEG onto PMMA microchannel surface to minimize nonspecific adsorption.

A dynamically modified microfluidic poly(dimethylsiloxane) chip with electrochemical detection for biological analysis.

The Use of Poly(dimethylsiloxane) Surface Modification with Gold Nanoparticles for the Microchip Electrophoresis.

Channel wall coating on a poly‐(methyl methacrylate) CE microchip by thermal immobilization of a cellulose derivative for size‐based protein separation