Abstract:For aluminium alloys, precipitation strengthening is controlled by age-hardening heat treatments, including solution treatment, quenching, and ageing. In terms of technological applications, quenching is considered a critical step, because detrimental quench-induced precipitation must be avoided to exploit the full age-hardening potential of the alloy. The alloy therefore needs to be quenched faster than a critical cooling rate, but slow enough to avoid undesired distortion and residual stresses. These contrary requirements for quenching can only be aligned based on detailed knowledge of the kinetics of quench-induced precipitation. Until the beginning of the 21st century, the kinetics of relevant solid-solid phase transformations in aluminium alloys could only be estimated by ex-situ testing of different properties. Over the past ten years, significant progress has been achieved in this field of materials science, enabled by the development of highly sensitive differential scanning calorimetry (DSC) techniques. This review presents a comprehensive report on the solid-solid phase transformation kinetics in Al alloys covering precipitation and dissolution reactions during heating from different initial states, dissolution during solution annealing and to a vast extent quench-induced precipitation during continuous cooling over a dynamic cooling rate range of ten orders of magnitude. The kinetic analyses are complemented by sophisticated micro- and nano-structural analyses and continuous cooling precipitation (CCP) diagrams are derived. The measurement of enthalpies released by quench-induced precipitation as a function of the cooling rate also enables predictions of the quench sensitivities of Al alloys using physically-based models. Various alloys are compared, and general aspects of quench-induced precipitation in Al alloys are derived.

Room temperature precipitation in quenched Al-Cu-Mg alloys: a model for the reaction kinetics and yield strength development

Atomic-scale study on the precipitation behavior of an Al-Zn-Mg-Cu alloy during isochronal aging

Quantitative Evaluation of Precipitates in an Al–Zn–Mg–Cu Alloy after Isothermal Aging

Early-Stage Precipitation Phenomena and Composition-Dependent Hardening in Al-Mg-Si-(Cu) Alloys

Effect of quenching rate on strengthening behavior of an Al-Zn-Mg-Cu alloy during natural ageing

Influence of Mg and Cu on Precipitation Behaviors and Mechanical Properties of Al-Si Alloys

Quench Sensitivity and Its Effect on the Microstructure and Mechanical Properties of an Al-Zn-Mg-Cu Aluminum Alloy

Influence of Quenching Temperature on Peak Aging Time and Hardness of Al-Mg-Si-Cu Alloys Strengthened by Nano-Sized Precipitates

Review of the Quench Sensitivity of Aluminium Alloys: Analysis of the Kinetics and Nature of Quench-Induced Precipitation

Clustering and Precipitation during Early-Stage Artificial Aging of Al–Si–Mg(–Cu) Foundry Alloys

Solute Clustering in Al–Cu–Mg Alloys During the Early Stages of Elevated Temperature Ageing

Development of Precipitation Hardening Parameters for High Strength Alloy AA 7068

High-Resolution Electron Microscopy and Kinetic Studies of Precipitation Hardening Reactions in Cast Al-5.8Zn-2.2Mg-2.5Cu

Temperature-dependent Constitutive Behavior with Consideration of Microstructure Evolution for As-Quenched Al-Cu-Mn Alloy

Characterisation of Precipitation Hardening Response and As-Quenched Microstructures in Al-Mg(-Ag) Alloys

Quantifying Early-Stage Precipitation Strengthening of Al–Mg–Zn(-Cu) Alloy by Using Particle Size Distribution

Effect of Ageing Temperature on Precipitation of Al-Cu-Li-Mn-Zr Alloy

Quench rate sensitivity of age-hardenable Al-Zn-Mg-Cu alloys with respect to the Zn/Mg ratio: An in situ SAXS and HEXRD study

Precipitation Hardening Behavior and Microstructure Evolution of Al–5.1 Mg–0.15Cu Alloy with 3.0zn (wt%) Addition

Constitutive Behavior for Quenching of Al–Cu–Mg Alloy With Consideration of Precipitation

Kinetic Study of Phase Transformation of Al-Zn-Mg-Cu Alloy during Quenching Process