Abstract:Research highlights ► Firstly, a non-precious metal catalyst LaNi 0.8 Co 0.2 O 3 exhibits excellent electrochemical activity with respect to the oxygen reduction reaction (ORR). ► Secondly, maximum power densities of 114.5 mW cm −2 at 30 °C and 151.3 mW cm −2 at 62 °C were obtained. ► Lastly, good stability (300-h stable performance at 20 mA cm −2 ) was exhibited. Abstract A perovskite-type oxide LaNi 0.8 Co 0.2 O 3 is prepared as a direct borohydride fuel cell (DBFC) cathode catalyst. Its electrochemical properties are studied by cyclic voltammetry. The results demonstrate that LaNi 0.8 Co 0.2 O 3 exhibits excellent electrochemical activity with respect to the oxygen reduction reaction (ORR) and good tolerance of BH 4 − ions. Maximum power densities of 114.5 mW cm −2 at 30 °C and 151.3 mW cm −2 at 62 °C are obtained, and good stability (300-h stable performance at 20 mA cm −2 ) is also exhibited, which shows that such perovskite-type oxides as LaNi 0.8 Co 0.2 O 3 can be excellent catalysts for DBFCs. Keywords Direct borohydride fuel cell Oxygen reduction reaction Perovskite-type oxide Cathode catalyst 1 Introduction Fuel cells have attracted significant attention for their high efficiency in converting chemical energy into electricity compared with the efficiency of hydrogen combustion engines. However, the successful large-scale commercialisation of fuel cells has been hindered by the scarcity of precious metal catalysts [1,2] and the easy degradation of these catalysts by contamination originating in the fuel [3,4] . Therefore, great interest has been focused on the research of non-precious metal catalysts as a substitute in fuel cells. Direct borohydride fuel cells (DBFCs) are fuel cells that can use non-precious metal catalysts for both their cathode and anode. The low-cost catalyst MnO 2 has been reported to exhibit sufficient oxygen reduction reaction (ORR) activity and feeble activity with respect to BH 4 − oxidation [5,6] . Moreover, macrocyclic compounds, including Fe/CoTMPP [7,8] , Fe/CoPc [9,10] and Fe/Co-PPY-C [11] , have been reported to exhibit good electrocatalytic activities toward the ORR. The results revealed by Lefevre et al. show that Fe–N–C catalysts can match the performance of an outstanding Pt/C catalyst system [12,13] . Apart from these metal–support catalysts, non-metal catalysts, such as vertically aligned nitrogen-containing carbon nanotubes, could also be used as efficient ORR electrocatalysts [14] . Perovskite-type oxides were considered as promising catalysts for ORR due to their sufficient electrical conductivity and good electrochemical properties [15] . LaNi x Co (1− x ) O 3 ( x = 0.1–0.9) is one of these type oxides. It can serve as an excellent catalyst in some high-temperature reaction such as the reaction of solid oxide fuel cells cathode [16] and the oxidation of light hydrocarbons including CO 2 reforming of methane [17] , carbon monoxide oxidation [18] , propane deep oxidation [19] and so on. However, the data regarding LaNi x Co (1− x ) O 3 ( x = 0.1–0.9) applications in the low-temperature ORR are still scarce. This paper reports new progress in the research of the perovskite-type oxide LaNi 0.8 Co 0.2 O 3 as a cathode catalyst for DBFCs. 2 Experimental details 2.1 Catalyst preparation The preparation of the perovskite-type oxide is described in previous works [15,20,21] . LaNi 0.8 Co 0.2 O 3 was synthesised by the sol–gel method. LaCoO 3 and LaNiO 3 were also prepared as references. Lanthanum nitrate (La(NO 3 ) 3 ·6H 2 O), nickel nitrate (Ni(NO 3 ) 2 ·6H 2 O) and cobalt nitrate (Co(NO 3 ) 2 ·6H 2 O) were used as raw materials. The anode catalyst cobalt (II) oxide [22] was purchased from J&K Chemical Ltd. 2.2 Electrode preparation The cathode consisted of a gas diffusion layer, a current collector and an active layer. The gas diffusion layer was prepared by mixing 60 wt.% acetylene black and 40 wt.% polytetrafluoroethylene (PTFE) (solid quality), then pressing the slurry into a 0.3-mm membrane and heating at 340 °C for 1 h. The active layer was prepared by mixing 30 wt.% catalyst, 45 wt.% carbon nanotubes and 25 wt.% PTFE (solid quality) into a paste. The pastes was then smeared onto a nickel foam and dried at 80 °C for 2 h under vacuum. The cathode electrode was finished by rolling the gas diffusion layer and the prepared nickel foam into a 0.6-mm sheet. The anode was prepared by the following steps: 97 wt.% cobalt (II) oxide and 3 wt.% PTFE were mixed together. The mixture was pasted onto the nickel foam, then dried at 80 °C for 2 h under vacuum. The anode electrode was then pressed under a pressure of 3 MPa for 1 min. 2.3 Characterisation of catalyst The X-ray diffraction of LaCoO 3 , LaNi 0.8 Co 0.2 O 3 and LaNiO 3 were conducted with a diffractometer (D/MAX-2400, Japan) using a CuKα ( λ = 1.5444 Å) source, and the diffraction signals were recorded in the 2 θ ranging 10–80°. The particle size and morphology of the samples were observed by field emission scanning electron microscope (FE-SEM, JSM-6700F). 2.4 Electrochemical measurements Cyclic voltammetry (CV), which was measured using an electrochemical workstation (CHI650C, ChenHua, Shanghai, China), was employed to characterise the electrochemical properties of LaNi 0.8 Co 0.2 O 3 . A standard three-electrode system was used in these electrochemical measurements. In the CV tests, a glassy carbon (GC) electrode modified with a cathode catalyst, a graphite electrode or Pt wire and a Hg/HgO electrode were used as the working electrode, counter electrode and reference electrode, respectively. The modified GC electrode was fabricated as following: a catalyst ink was prepared by ultrasonically mixing 3 mg catalyst, 0.5 ml ethanol and 15 μl Nafion (5 wt.%) into a slurry, then spreading 10 μl of the slurry onto the surface of the glass carbon electrode. Before the tests, oxygen was eliminated or enriched by bubbling nitrogen gas or air into the electrolyte solution for 20 min. To evaluate the performance of the cells that consisted of these perovskite-type oxides as cathodes and cobalt (II) oxide as anodes, polarisation curves were collected by a battery testing system (from Neware Technology Limited, Shenzhen, China). The test was conducted in a container with a 1-cm 2 window, where the cathodes were placed. The gas diffusion layer of the cathode was exposed to air, whereas the active layer was in contact with the electrolyte fuel. The anode was placed inside the container, facing the cathode and 2 cm away from it. The detailed structure of the fuel cell can be verified in [9] . The oxygen and fuel flow rates were 5 sccm and 20 ml min −1 , respectively. 3 Results and discussion Fig. 1 shows the XRD patterns of LaCoO 3 , LaNi 0.8 Co 0.2 O 3 and LaNiO 3 . The patterns change from the perovskite-type LaCoO 3 phase (JCPDS, PDF code: 048-0123) to the perovskite-type LaNiO 3 phase (JCPDS, PDF code: 33-0710) with increasing Ni concentration, which indicates that the synthesis method can be used to obtain perovskite-type oxides. It is also found that minor peaks of La 2 O 3 phase (JCPDS, PDF code: 01-089-4016), NiO (JCPDS, PDF code: 00-044-1159), La(OH) 3 (JCPDS, PDF code: 00-006-0585) and La 2 NiO 4 (JCPDS, PDF code: 01-080-0065) in Fig. 1 which suggests that the samples are not a single phase structure. Fig. 2 shows the morphology of LaCoO 3 , LaNi 0.8 Co 0.2 O 3 and LaNiO 3 and globular particles is displayed uniformly with average diameter around 80–100 nm. Fig. 3 (a) shows cyclic voltammograms of the glassy carbon (GC) electrode modified with a LaNi 0.8 Co 0.2 O 3 catalyst in 1 M KOH solution under air saturation. It has deducted the background currents which were obtained with a GC in the nitrogen-saturated electrolyte. The result shows two intense reduction peaks at ca. −0.246 V and ca. −0.688 V (vs. Hg/HgO, 6 M KOH), which represents the reduction of O 2 to O 2 − (reaction (1) ) and O 2 to HO 2 − (reaction (2) ), respectively [23–26] . (1) O 2 + e − → O 2 − (2) O 2 + H 2 O + 2 e − → HO 2 − + OH − It can be concluded from Fig. 3 (a) that LaNi 0.8 Co 0.2 O 3 has excellent electrochemical activity toward the ORR. Another essential characteristic for the cathode catalyst is tolerance of the fuel solution (KBH 4 + KOH), which makes DBFCs successful membraneless structures that avoid using precious ion exchange membranes [6,9,10] . Fig. 3 (b) shows the cyclic voltammograms of the GC electrode modified with LaNi 0.8 Co 0.2 O 3 in fuel solution (0.1 M KBH 4 + 1 M KOH) and electrolyte solution (1 M KOH), respectively. To eliminate the influence of the oxygen reduction reaction, the solution was saturated with nitrogen gas to exclude oxygen. There is no apparent oxidation peak, which indicates that LaNi 0.8 Co 0.2 O 3 does not react with BH 4 − and can, therefore, tolerate BH 4 − . The performances of the cells fabricated with LaCoO 3 , LaNi 0.8 Co 0.2 O 3 and LaNiO 3 as their cathode and CoO as their anode are illuminated in Fig. 4 , and the maximum power densities of 87.7, 114.5 and 106.9 mW cm −2 were obtained at room temperature for each cell, respectively. For comparison, some published data of DBFC using MnO 2 as cathode and hydrogen storage alloys as anode [27] was also demonstrated in Fig. 4 . It is obvious that much higher max power densities were obtained when LaNi x Co (1− x ) O 3 ( x = 0, 0.8, 1) were used as cathode. To the best of our knowledge, the electrochemical activity of perovskite-type oxide is determined by electrical and ionic conductivity [16] . LaNiO 3 and LaNi 0.8 Co 0.2 O 3 have higher maximum power densities than LaCoO 3 because LaNiO 3 has a low electrical resistance and metallic-like conductivity [16,28] . LaNi 0.8 Co 0.2 O 3 as a cathode in the membraneless DBFC showed the best performance due to Ni substitutions, which induce lattice defects and consequently increase the concentration of oxygen vacancies. Thus, both ionic conductivity and the presence of main active sites are enhanced by the increased concentration of oxygen vacancies. Therefore, LaNi 0.8 Co 0.2 O 3 shows the best electrochemical activity among these series catalysts. Fig. 5 shows the performance of a LaNi 0.8 Co 0.2 O 3 -catalysed cathode at different temperatures. It distinctly shows that the maximum power density increases with increasing temperature due to the enhanced kinetics of the oxidation/reduction reaction and mass transfer of the reactant. The maximum power densities are 114.5, 130.3 and 151.3 mW cm −2 at 30, 43 and 62 °C, respectively. The stability of the LaNi 0.8 Co 0.2 O 3 -catalysed cathode has been studied through life-time experiments. The fuel solution was refreshed every 24 h, and data points were randomly picked. Fig. 6 shows that LaNi 0.8 Co 0.2 O 3 maintains good stability over a 300-h test, which is ascribed to its outstanding tolerance for BH 4 − and remarkable corrosion-proof ability against OH − . As a comparison, Fig. 6 also shows the DBFC life-time experiments of Co(OH) 2 -PPY-C [11] and Pt/C [29] as the cathode catalyst. It obviously shows that fuel cell have much better performance stability when LaNi 0.8 Co 0.2 O 3 was used as cathode. 4 Conclusions In summary, a perovskite-type oxide LaNi 0.8 Co 0.2 O 3 was synthesised by the sol–gel method. The electrochemical measurements show that LaNi 0.8 Co 0.2 O 3 has excellent catalytic activity for the oxygen reduction reaction and good borohydride tolerance. Maximum power densities of 114.5 mW cm −2 at 30 °C and 151.3 mW cm −2 at 62 °C were obtained. In addition, good stability was shown through galvanostatic discharge testing under ambient conditions. References [1] H.A. Gasteiger S.S. Kocha B. Sompalli F.T. Wagner Appl. Catal. B: Environ. 56 2005 9 35 [2] B.C.H. Steele A. Heinzel Nature 414 2001 345 352 [3] X.W. Yu S.Y. Ye J. Power Sources 172 2007 133 144 [4] X.W. Yu S.Y. Ye J. Power Sources 172 2007 145 154 [5] K. Matsuki H. Kamada Electrochim. Acta 31 1986 13 18 [6] R.X. Feng H. Dong Y.D. Wang X.P. Ai Y.L. Cao H.X. Yang Electrochem. Commun. 7 2005 449 452 [7] H. Cheng K. Scott J. Electroanal. Chem. 596 2006 117 123 [8] R.K. Raman A.K. Shukla J. Appl. Electrochem. 35 2005 1157 1161 [9] J.F. Ma J. Wang Y.N. Liu J. Power Sources 172 2007 220 224 [10] J.F. Ma Y.N. Liu P. Zhang J. Wang Electrochem. Commun. 10 2008 100 102 [11] H.Y. Qin Z.X. Liu L.Q. Ye J.K. Zhu Z.P. Li J. Power Sources 192 2009 385 390 [12] H.A. Gasteiger N.M. Markovic Science 324 2009 48 49 [13] M. Lefevre E. Proietti F. Jaouen J.P. Dodelet Science 324 2009 71 74 [14] K.P. Gong F. Du Z.H. Xia M. Durstock L.M. Dai Science 323 2009 760 764 [15] J. Ma Y. Liu Y. Yan P. Zhang Fuel Cells 8 2008 394 398 [16] M. Hrovat N. Katsarakis K. Reichmann S. Bernik D. Kuscer J. Holc Solid State Ionics 83 1996 99 105 [17] G. Valderrama A. Kiennemann M.R. Goldwasser J. Power Sources 195 2009 1765 1771 [18] T. Vaz A.V. Salker Med. Maladies Infect. 37 2007 81 84 [19] A. Boreave H. Tan V. Roche P. Vernoux J.P. Deloume Solid State Ionics 179 2008 1071 1075 [20] Y. Liu J.F. Ma J.H. Lai Y.N. Liu J. Alloys. Compd. 488 2009 204 207 [21] L. Yan L. Yongning M. Jinfu L. Junhua J. Power Sources 195 2010 1854 1858 [22] L. Sai L. Yongning L. Yan C. Yuanzhen J. Power Sources 195 2010 7202 7206 [23] T. Ohsaka L.Q. Mao K. Arihara T. Sotomura Electrochem. Commun. 6 2004 273 277 [24] J. Xu W.H. Huang R.L. McCreery J. Electroanal. Chem. 410 1996 235 242 [25] K. Vaik D.J. Schiffrin K. Tammeveski Electrochem. Commun. 6 2004 1 5 [26] Y. Wang D. Zhang H.Q. Liu J. Power Sources 195 2010 3135 3139 [27] Y.G. Wang Y.Y. Xia Electrochem. Commun. 8 2006 1775 1778 [28] Y. Matsumoto H. Yoneyama H. Tamura J. Electroanal. Chem. 83 1977 167 176 [29] H. Cheng K. Scott K. Lovell Fuel Cells 6 2006 367 375

Abstract:Cathode material Pr 2 Ni 0.6 Cu 0.4 O 4 (PNCO) for intermediate-temperature solid oxide fuel cells (IT-SOFCs) is synthesized by a glycine–nitrate process using Pr 6 O 11 , NiO, and CuO powders as raw materials. X-ray diffraction analysis reveals that nanosized Pr 2 Ni 0.6 Cu 0.4 O 4 powders with K 2 NiF 4 -type structure can be obtained from calcining the precursors at 1000 °C for 3 h. Scanning electron microscopy shows that the sintered PNCO samples have porous microstructure with a porosity of more than 30% and grain size smaller than 2 μm. A maximum conductivity of 130 S cm −1 is obtained from the PNCO samples sintered at 1050 °C. A single fuel cell based on the PNCO cathode with 30 μm Sm 0.2 Ce 0.8 O 1.9 (SCO) electrolyte film and a 1 mm NiO–SCO anode support is constructed. The ohmic resistance of the single Ni–SCO/SCO/PNCO cell is 0.08 Ω cm 2 and the area specific resistance (ASR) value is 0.19 Ω cm 2 at 800 °C. Cell performance was also tested using humidified hydrogen (3% H 2 O) as fuel and air as oxidant. The single cell shows an open circuit voltage of 0.82 V and 0.75 V at 700 °C and 800 °C, respectively. Maximum power density is 238 mW cm −2 and 308 mW cm −2 at 700 °C and 800 °C, respectively. The preliminary tests have shown that Pr 2 Ni 1− x Cu x O 4 materials can be a good candidate for cathode materials of IT-SOFCs. Keywords Solid oxide fuel cell Cathode materials Glycine–nitrate process Electrochemical performance 1 Introduction Solid oxide fuel cell has been considered as one of the most promising energy conversion devices due to their high energy conversion efficiency, less emission of pollutants and flexibility of fuels [1,2] . In particular, the possibility of direct utilization of hydrocarbon and renewable fuels (e.g., methane and ethanol) will greatly reduce the cost of SOFC technology [3] . A conventional SOFC generally operates at high temperature (>800 °C), which not only leads to complex material degradation and reaction, but also limits material choice of the cell components [4] . Therefore, much work has been done to reduce the operating temperature of SOFC to low to intermediate temperature range (600–800 °C). However, as the operating temperature decreases, the cathode overpotential and interfacial resistances between the electrolyte and electrodes, especially cathode, also increase, leading to lower cell performance [5] . There are two ways to solve this problem. One is to use composite cathode materials to increase the areas of the triple phase boundary (TPB). Another is to find new mixed oxygen ionic and electronic conducting (MIEC) materials, which have rapid surface exchange kinetics, high oxygen vacancy concentration, and extended TPB from the gas/electrode/electrolyte interface to the total external electrode surface area [6,7] . Recently, A 2 MO 4 oxides have received considerable attention in using as cathode materials for solid oxide fuel cells due to their interesting mixed transport properties [8] . The A 2 MO 4 oxides, with M a transition metal cation like Ni and A, a lanthanide or alkaline earth, characterizes some oxygen over stoichiometry and a mixed valence of M in the compound [6] . The crystal structure of A 2 MO 4 oxides can be described as taking of perovskite layers alternating with NaCl (rock salt) layers. For a mixed oxygen–ionic and electronic conductor (MIEC) as the A 2 MO 4 oxide, the change of composition or oxidation–reduction treatments can greatly affect the transport properties, and the cathode reaction O 2 + 4e − = 2O 2 − occurs at the gas–MIEC two-phase interface, whereas it takes place only at a triple-phase boundary if the cathode is a pure electronic conductor [8,9] . In this way, several systems have been proposed either by doping at the A position with alkaline-earths and with other rare earths like Nd or Pr or by doping in the M position with other transition metals, typically Cu and Co, leading to dramatic changes of the structural and physical properties. Ishihara et al. reported that among different rare earth cations at the A-site, those incorporated Pr 3+ exhibit the highest electrical conductivity and the lowest overpotential values [10,11] . Therefore, a combination of Pr for A-site and Cu for M-site material Pr 2 Ni 1− x Cu x O 4 is expected to bring better electrochemical properties as a cathode material at intermediate temperature. Aguadero et al. investigated the electrochemical property of La 2 Ni 1− x Cu x O 4 materials and reported that among the La 2 Ni 1− x Cu x O 4 ( x = 0–1.0) system, the La 2 Ni 0.6 Cu 0.4 O 4 composition exhibits the highest electrical conductivity [8] . In this paper, Pr 2 Ni 0.6 Cu 0.4 O 4 (PNCO) powders were synthesized by a glycine–nitrate methods. The microstructure and electrochemical property of the sintered PNCO material, including the electrical conductivity, the ohmic resistance and the electrode interfacial resistance were investigated, and single cells based on the PNCO cathode were also constructed and tested [12] . 2 Experimental 2.1 Sample preparation Pr 2 Ni 0.6 Cu 0.4 O 4 powder was prepared by a glycine nitrate method using Pr 6 O 11 (AR), NiO (AR), CuO (AR) powders, HNO 3 (AR) and C 2 H 5 NO 2 (AR) as raw materials. Stoichiometry chemicals were dissolved into nitric acid to get a nitrate solution. Then glycine was added into the solution to form a transparent and homogeneous solution, which was subsequently heated and the viscosity of the solution increases gradually [13] . As temperature rises, a self-sustaining combustion finally occurs in the viscous gels and dark precursor powders were obtained. The precursor powders were then calcined at 1000 °C for 3 h to remove residue organics and form a stable crystalline structure. The calcined powders were subsequently pressed in a rigid die, and the compacts were then sintered at 900–1050 °C for 2 h for later test. Commercial NiO (2.5 μm) and Sm 0.2 Ce 0.8 O 1.9 (SCO, prepared by the gel-casting process, 30 nm) powders were employed to prepare the NiO/SCO anode substrates. After mechanically blending (NiO:SCO = 60:40 wt%), the powder mixes were compacted in a steel die with 18 mm in diameter, the green anode substrates were fired at 1000 °C for 2 h. SCO electrolyte slurry was prepared onto the fired NiO/SDC substrates by a dip-coating method. The coated samples were then co-sintered at 1400 °C for 4 h to obtain anode/electrolyte bilayer structure with dense SCO electrolyte film supported on porous NiO/SCO substrates. After screen-printing Pr 2 Ni 0.6 Cu 0.4 O 4 slurry onto the electrolyte side of the NiO/SCO bilayer and subsequently sintering at 1050 °C for 2 h, single cells were obtained [14] . The active area of the cathode in the single cells was 0.24 cm 2 . Thickness of the anode, the cathode and the electrolyte in the single cell is about 1 mm, 100 μm and 30 μm, respectively. 2.2 Sample characterization Phase structure of the precursors and the calcined Pr 2 Ni 0.6 Cu 0.4 O 4 powders were characterized by X-ray diffraction analysis (XRD). Porosity of the PNCO samples sintered at different temperatures was tested using the Archimedes method with a theoretical density of Pr 2 Ni 0.6 Cu 0.4 O 4 taken as 7.38 g cm −3 , which was calculated according data obtained from the XRD pattern. Microstructure of the PNCO samples sintered at different temperature was observed by scanning electron microscope (SEM, Sirion 200). Electrical conductivity of the sintered PNCO samples was measured using the four-probe method. Single cell performance was tested using a house-made fuel cell testing device, with humidified hydrogen (3% H 2 O) as the fuel and steady air as the oxidant. Impendence spectra of the single cells were also tested using an electrochemical workstation (Chenhua 604A) under open-circuit conditions over a frequency range from 0.01 Hz to 1 MHz, with signal amplitude of 10 mV. The spectra were simulated by the Zsimpwin software. 3 Results and discussions 3.1 XRD analysis Fig. 1 shows XRD patterns of the precursors and the calcined Pr 2 Ni 0.6 Cu 0.4 O 4 powders. There exist some peaks of miscellaneous phases in the XRD patterns of the precursor powders. This indicates that the chemicals did not react completely during the self-sustaining combustion. It can be seen from Fig. 1 that as the calcining temperature increases, miscellaneous phases reduce. And when calcining temperature increases to 1000 °C, only K 2 NiF 4 -type structure was observed in the XRD patterns. The samples retained the K 2 NiF 4 -type structure when the calcining temperature increases to 1100 °C. But the diffraction peaks become sharper and narrower than those of 1000 °C, which indicates grain growth of the calcined powders. According to the crystalline structure and the molecular formula of the PNCO powders, the grain parameters were calculated. The lattice content values are a = 5.456, b = 5.392, c = 12.446, α = 90°, β = 90°, γ = 90°. The grain size of the PNCO powders calcined at 1000 °C is 29.02 nm based on the Scherrer Formula. And the theoretical density of the PNCO powders is calculated to be 7.38 g cm −3 . 3.2 Porosity and microstructure of the sintered PNCO samples Table 1 lists relative density and open porosity of the Pr 2 Ni 0.6 Cu 0.4 O 4 samples sintered at different temperature. As sintering temperature increases, the samples become dense. While the samples sintered at 900 °C have an open porosity of 51%, the samples sintered at 1100 °C only have an open porosity of 27%. Fig. 2 shows SEM microstructure of the PNCO samples sintered at different temperature. All of the sintered samples have porous structure. This porous structure can facilitate the diffusion of oxidant gases and extend the area of the triple-phase boundary (TPB). However, as the sintering temperature increases, the porosity of the PNCO samples deceases. This is consistent with the results listed in Table 1 . It can also be seen from Fig. 2 that the samples sintered at lower temperature have a smaller grain size. Average grain sizes of the PNCO samples sintered at 900 °C, 1000 °C, 1050 °C and 1100 °C is about 0.7, 0.8, 1.0 and 1.5 μm, respectively. 3.3 Electrical conductivity Electrical conductivity ( σ ) of the sintered Pr 2 Ni 0.6 Cu 0.4 O 4 samples was measured in air by the four-probe method in the temperature range from 500 to 800 °C. Fig. 3 shows electrical conductivity as a function of testing temperature of the PNCO samples. As the sintering temperature of the PNCO samples increases, electrical conductivity increases gradually. A maximum conductivity of 130 S cm −1 was got for samples sintered at 1050 °C under testing temperature 500 °C. As sintering temperature increases, the samples become dense and the grain grows, which are beneficial to the transfer of ions and electrons, thus leading to the increase of electrical conduction. However, when the sintering temperature increases to 1100 °C, the conductivity of the sample becomes lower than that sintered at 1050 °C. This may be caused by the loss of surface area of grain boundaries, which results from the grain growth as sintering temperature. It can also be seen from Fig. 3 that conductivity of the PNCO samples decreases as measuring temperature increases, which indicates the electron conduction of the PNCO materials. Boehm et al. reported that La 2 Ni 0.6 Cu 0.4 O 4 material with K 2 NiF 4 -type structure has a conductivity of 87 S cm −1 at 580 °C [6] . This value is lower than the conductivity value of Pr 2 Ni 0.6 Cu 0.4 O 4+ δ obtained in this work (about 130 S cm −1 ). This may be caused by the different ionic of La 3+ (1.06 Å) with Pr 3+ (1.01 Å) and the additional contribution of the Pr 3+ /Pr 4+ valence change [11] . Average conduction activation energy was calculated from the ln σ and T −1 values, and the result is about 0.189, 0.137,0.110 and 0.114 eV for PNCO samples sintered at 900 °C, 1000 °C 1050 °C and 1100 °C for 2 h, respectively. The low-temperature sintered samples show slightly high resistant potential. This is consistent with the ionic conduction values. 3.4 Impedance spectra results Fig. 4 shows impedance spectra of the NiO–SCO/SCO/PNCO single cell at 800 °C in air. The high-frequency intercept with the real axis represents the ohmic losses, and the difference between the high frequency and low frequency intercepts denotes the total electrode interfacial resistances in the cell. The ASR value obtained in this work is the total electrode resistance. It includes the contribution of the anode and the cathode. Min Chen et al. have reported the ASR values of Ni/SDC electrodes [15] , which is about 0.12 Ω cm 2 for a Ni/SDC anode with 60% NiO. In this work we simply use this value as the anode ASR of the single cell we prepared, and because the total ASR value of the single cell tested is 0.19 Ω cm 2 , the cathode ASR value was calculated to be about 0.07 Ω cm 2 . It has been reported that the ASR value of the La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 material is about 0.30 Ω cm 2 [16] . By comparison, ASR value of the PNCO material is much lower. The lower ASR value of the PNCO material makes it have high-electrocatalytic activity for oxygen-reduction reactions at intermediate temperatures. The excellent cathodic performance of the PNCO material can be ascribed to the fast oxygen diffusion in the bulk and the high surface kinetics on the surface of electrode. Moreover, as a MIEC oxide, PNCO provides multiple pathways for the oxygen ions to migrate to the electrode/electrolyte interface. 3.5 Single cell performance Fig. 5 shows the open circuit voltage (OCV) and power densities of a single solid oxide fuel cell with humidified hydrogen (3% H 2 O) as fuel and air as the oxidant in the temperature range of 500–800 °C. The single cell shows a maximum open circuit voltage of 0.82 V and 0.75 V at 700 °C and 800 °C, respectively. However, with increasing testing temperature, the OCV value deceases and is lower than the theoretical values. This may be due to the electronic penetration through SCO electrolyte. Maximum power densities of the cell were 238 and 308 mW cm −2 at 700 °C and 800 °C, respectively, indicating that good performance can be obtained for the single fuel cell using Pr 2 Ni 0.6 Cu 0.4 O 4 as cathode and SCO film as electrolyte. It has mentioned above that the ASR value of Pr 2 Ni 0.6 Cu 0.4 O 4 is lower than that of the La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 material. Therefore, the cell based on Pr 2 Ni 0.6 Cu 0.4 O 4 cathode shows a better performance than the traditional cathode La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 [15] . Fig. 6 shows cross-section microstructure of the single cell after testing. There exists a good combination between the electrodes and the electrolyte. 4 Conclusions Pr 2 Ni 0.6 Cu 0.4 O 4 (PNCO) powders with K 2 NiF 4 -type structure were successfully synthesized by a glycine–nitrate method. Sintered PNCO samples have porous structure and good electrical conductivity. A maximum electrical conductivity of 130 S cm −1 was obtained at 500 °C in air. There exist low ohmic resistance and electrode interfacial resistance of 0.08 Ω cm 2 and 0.19 Ω cm 2 , respectively. A single fuel cell based on the PNCO cathode with a 30 μm Sm 0.2 Ce 0.8 O 1.9 electrolyte and a 1 mm thickness NiO–SCO anode was constructed. The single cell shows an open circuit voltage of 0.82 V and 0.75 V and maximum power density of 238 mW cm −2 and 308 mW cm −2 at 700 °C and 800 °C, respectively. The present work has shown that the PNCO materials may be a favorable candidate for cathode material of intermediate temperature solid oxide fuel cells. Acknowledgements This work was financially supported by the Natural Science Foundation of Anhui Province (contract No. 070414186), the Program of Science and Technology of Anhui Province (contract No. 2008AKKG0332), the Nippon Sheet Glass Foundation for Materials Science and Engineering (NSCF) (contract No. 070304B2) and the Open Project Program of Key Laboratory of Low Dimensinal Materials & Application Technology (Xiangtan University), Ministry of Education of China under contract No. DWKF0802. References [1] P. Bansal Narottam Z.M. Zhong J. Power Sources 158 2006 148 153 [2] C. Cacciola V. Antonucci S. Freni J. Power Sources 100 2001 67 79 [3] S.P. Jiang Y.M. Ye T.M. He S.B. Ho J. Power Sources 185 2006 1 [4] S. Yang T.M. He Q. He J. Alloys Compd. 450 2008 400 404 [5] Q.J. Zhou T.M. He Q. He Y. Ji Electrochem. Commun. 11 2009 80 83 [6] H. Zhao F. Mauvy C. Lalanne J.M. Bassat S. Fourcad J.C. Grenier Solid State Ionics 179 2008 35 36 [7] H.A. Hamedani K.H. Dahmen D. Li H. Peydaye-Saheli H. Garmestani M. Khaleel Mater. Sci. Eng. B: Adv. Funct. Solid-State Mater. 153 2008 1 3 [8] A. Aguadero J.A. Alonso M.J. Escudero L. Dazaet Solid State Ionics 179 2008 11 12 [9] J. Wan J.B. Goodenough J.H. Zhu Solid State Ionics 178 2007 281 286 [10] C.J. Zhu X.M. Liu D. Xu D.T. Yan D.Y. Wang W.H. Su Solid State Ionics 179 2008 1470 1473 [11] T. Ishihara T. Kudo H. Matsuda Y. Takita J. Electrochem. Soc. 142 1995 1519 1523 [12] Y. Tao H. Nishino S. Ashidate H. Kokubo M. Watanabe H. Uchida Electrochim. Acta 54 2009 3309 3315 [13] B. Yu W.Q. Zhang J.M. Xu J. Chen Int. J. Hydrogen Energy 33 2008 6873 6877 [14] Tietz F. Haanappel V.A.C. Mai A. Mertens J. Stover J. Power Sources 156 2006 20 22 [15] J.D. Zhang Y. Ji H.B. Gao T.M. He J. Liu J. Alloys Compd. 395 2009 322 [16] E.P. Murray M.J. Sever S.A. Barnett Solid State Ionics 148 2002 27 34

LaNi0.8Co0.2O3 as a cathode catalyst for a direct borohydride fuel cell

LaNi0.9Ru0.1O3 As a Cathode Catalyst for a Direct Borohydride Fuel Cell

Development of High-Performance Cathode Catalyst of Polypyrrole Modified Carbon Supported CoOOH for Direct Borohydride Fuel Cell

Perovskite Structure LaNi0.5Fe0.5O3 Electrocatalyst for Rechargeable Li-O2 Batteries

CoO nanorods/C as a high performance cathode catalyst in direct borohydride fuel cell

Study of LaCoO3 As a Cathode Catalyst for a Membraneless Direct Borohydride Fuel Cell

La1-xSrxCoO3 (x = 0.1-0.5) as the cathode catalyst for a direct borohydride fuel cell

Investigation of La0.6Sr0.4Co1-xNixO3-δ (x=0, 0.2, 0.4, 0.6, 0.8) catalysts on solid oxide fuel cells anode for biogas dry reforming

LaFe 1– x Co x O 3 Perovskite Nanoparticles Supported on Ni(OH) 2 as Electrocatalyst for the Oxygen Evolution Reaction

Oxygen reduction reaction activity of La-based perovskite oxides in alkaline medium : a thin-film rotating ring-disk electrode study

Two 3D Structured Co-Ni Bimetallic Oxides As Cathode Catalysts for High-Performance Alkaline Direct Methanol Fuel Cells

Ammonia Tolerant Oxygen Reduction Reaction Studies on Metal Oxide Catalysts in Alkaline Media Using the Gas Diffusion Electrode Half Cell

Study on a Novel Double-Layer Anode for Solid Oxide Fuel Cells Based on CO2 Dry Reforming of Methane

Bifunctional electrocatalysts Pr0.5Sr0.5Cr0.1Fe1-xNixO3-δ (x=0.1,0.2) for HOR and ORR of a symmetric solid oxide fuel cell

In Situ Exsolved Core-Shell Nanoparticles on Perovskite Parent: A Novel High-Performance Anode for Solid Oxide Fuel Cells

Carbothermal Shock Synthesis of CoO/N/C Nanoparticles with Superior Durability for Oxygen Reduction Reaction

Cobalt-Doped Perovskite-Type Oxide LaMnO3 as Bifunctional Oxygen Catalysts for Hybrid Lithium-Oxygen Batteries

Robust Ni-doped Ruddlesden-popper (La,Sr)Fe1-xNixO4+δ oxide as solid oxide cells fuel electrode for CO2 electrolysis

Preparation and electrochemical performance of Pr2Ni0.6Cu0.4O4 cathode materials for intermediate-temperature solid oxide fuel cells

Cobalt–polypyrrole–carbon black (Co–PPY–CB) electrocatalysts for the oxygen reduction reaction (ORR) in fuel cells: Composition and kinetic activity

Anion Fluorine-Doped La<sub>0.6</sub>Sr<sub>0.4</sub>Fe<sub>0.8</sub>Ni<sub>0.2</sub>O<sub>3- </sub> Perovskite Cathodes with Enhanced Electrocatalytic Activity for Solid Oxide Electrolysis Cell Direct CO<sub>2</sub> Electrolysis