Abstract:This paper presents a numerical approach to simulate sliding friction between engineering surfaces with 3D roughness in point contacts. The numerical approach is developed on the basis of the deterministic solutions of mixed lubrication, which is able to predict the locations where the asperity contacts occur, and the pressure distribution over both lubrication and contact areas. If the friction coefficients over the contacting asperities have been determined, total friction force between the surfaces can be calculated by summing up the two components, i.e., the boundary friction contributed by contacting asperities and the shear stress in hydrodynamic regions. The fi-ictions from asperity contact were determined in terms of a limiting shear stress or shearstrength of boundary, films while the fluid shear stress in the lubrication areas was calculated using different rheology models for the lubricant, in order to find which one would be more reliable in predicting fluid tractions. The simulations covered the entire lubrication, regime, including full-film Elastohydrodynamic Lubrication (EHL), mixed lubrication, and boundary lubrication. The results, when being plotted as a function of sliding velocity, give a Stribeck-type friction curve. This provides an opportunity to study friction change during the transition of lubrication conditions and to compare friction performance oil different rough surpces, which is of great value in engineering practice. Experiments were conducted on a commercial test device-universal material tester (UMT) to measure friction at a fixed load but different sliding velocities in reciprocal or rotary motions. The results also give rise to the Stribeck friction curvesfor different rough surfaces, which are to be compared with the results from simulations. The samples were prepared with typical machined surfaces in different roughness heights and textures, and in point contacts with steel ball. Results show that there is a general agreement between the experiments and simulations. It is found that surface features, such as roughness amplitude and patterns, may have a significant effect on the critical speed of transition firom hydrodynamic to mixed lubrication. It? the regime of mixed lubrication, rougher samples would give rise to a higherfiriction if the operation conditions are the same.

The investigation of contact ratio in mixed lubrication

Contact Ratio of Rough Surfaces with Multiple Asperities in Mixed Lubrication at High Pressures

Analysis of the Rolling Interface Contact Characteristics in Mixed Lubrication Based on Gaussian Distribution Theory

A New Method for the Experimental Investigation of Contact in Mixed Lubrication

Frictional Behaviour of Engineering Surfaces in Overall Lubrication Regimes of Point Contacts

Traction Formula for Rolling-Sliding Contacts in Consideration of Roughness under Low Slide to Roll Ratios

Simulations And Measurements Of Sliding Friction Between Rough Surfaces In Point Contacts: From Ehl To Boundary Lubrication

Experimental Investigation of Lubrication Failure of Polyalphaolefin Oil Film at High Slide/Roll Ratios

Transition of frictional states and surface roughness effects in lubricated contacts

Experimental research of sliding friction coefficient of rough surface under lubricated point contact

Sliding or Rolling? Characterizing single-particle contacts

Effects of Surface Roughness on Sliding Friction in Lubricated-Point Contacts: Experimental and Numerical Studies

Substrate Surface Energy Effects on a Liquid Lubricant Film at Nanometre Scalesubstrate Surface Energy Effects on a Liquid Lubricant Film at Nanometre Scale

Experimental Investigation of Lubrication Properties at High Contact Pressure

Numerical Investigation of the Tribological Performance of Micro-Dimple Textured Surfaces under Hydrodynamic Lubrication

Effect of surface roughness on sliding friction in lubricated contacts-reciprocal experiment study

The Relationship Between Friction and Film Thickness in EHD Point Contacts in the Presence of Longitudinal Roughness

Evaluating the contact model for anisotropic non-Gaussian roughness in mixed lubrication regime

Lubrication State Identification of the Line Contact Tribo-Pair under a Pure Rolling Condition with Ultrasonic Method

Numerical Running-In Method for Modifying Cylindrical Roller Profile under Mixed Lubrication of Finite Line Contacts

Rolling, sliding & torsion of micron-sized silica particles - Experimental, numerical and theoretical analysis