Abstract:A high-temperature and high-pressure gas field in an oil field requires the use of super 13 chromium material due to corrosive environments. In the recent production process, there have been four consecutive cases of corrosion, fracture, and perforation of tubing nipples, which have brought enormous economic losses to the oilfield. This article analyzes the failure causes of these four tubing nipples and proposes preventive measures. In this paper, the macroscopic morphology, chemical composition, mechanical properties, metallography, and microscopic morphology of four failed tubing nipples have been analyzed. Combined with the field service conditions and string structure of the tubing nipples, it is believed that the failure of the tubing nipples is mainly due to the connection of carbon steel and stainless steel materials, forming a typical galvanic corrosion galvanic cell. The geometric and environmental factors of the materials exacerbate this corrosion. Eventually, severe galvanic corrosion occurred on the inner surface of the tubing nipple, resulting in severe wall thinning or partial perforation, and four tubing nipples failed. The failed tubing nipples in Wells A, B, and C have erosion marks, which are caused by the action of high pressure and high flow rate fluids in the well; The inner surface of the tubing nipple in Well D is rusty yellow, mainly due to the corrosion of its inner wall caused by the acid fracturing fluid injected earlier. At the same time, the string structure of four wells shows that the tubing nipple is located at the variable diameter node of the string. When the fluid in the well flows from the large hole into the smaller hole, the fluid in the well will change there, and its flow rate and pressure will also increase, further exacerbating the erosion in this area. With the development of deep wells containing carbon dioxide in oil fields and the application of carbon dioxide injection secondary oil recovery technology, the use of 13Cr martensitic stainless steel is also increasing. In order to avoid the occurrence of similar accidents that will bring huge economic losses to the oil field, it is recommended that the material of the pipe string (including accessories) of such wells be confirmed using a portable direct reading spectrometer before entering the well.

Analysis of Numeric Control Processing Technology for High Strength and High Chrome Oil Well Steel Tubing

Studies on Coated Cutting Tools and Processes for Internal Thread Milling the Super-Strength Steel

The Analytical Model of Ball-Spinning Force for Processing an Annular Groove on the Inner Wall of a Steel Tube

Corrosion Analysis and Prevention of Tubing Nipples in Four Wells

Technology Optimization Analysis of Three-Roll Rotary Piercing Process for Seamless Steel Pipe

Effect of Processing Technology on Mechanical Properties of HRB500 High-Strength Steel Bar Threading

Optimizing Design of the Cutting Tool in Cutting of Ultra-High Strength Steel Beam Part

Properties Requirement and Alloy Design for Organic Matter Cutting Tool Steel

Optimization of Machining Parameters of 2.25cr1mo0.25v Steel Based on Response Surface Method and Genetic Algorithm

Machining performance evaluation and tool wear analysis of dry cutting austenitic stainless steel with variable-length restricted contact tools

Analysis, modelling, and optimization of force in ultra-precision hard turning of cold work hardened steel using the CBN tool

Machinability study on hard milling of ultra-high strength steel 30CR3SiNiMoVA

Failure analysis of a high strength Cr-containing tube used in an oil well

Development and Application of Thermo-mechanical Control Process Involving Ultra-fast Cooling Technology in China

Integrating textured tools and diverse lubricooling approaches in machining performance of Ti and Ni-base alloys – a comprehensive review

Research on the Machining Ability for Rough Machining of Large Hydrogenated Cylindrical Shell Forging

Multi-Constrained Analysis Of Metal Cutting And Its Application

An investigation on wear mechanism of high-speed turning of free-cutting steel AISI 1215 using uncoated and multi-layer coated tools

Optimization of Surface Quality and Power Consumption in Machining Hardened AISI 4340 Steel

Evaluation of the optimal cutting performance of high-speed steel and tungsten carbide cutting tools in the machining of AISI 304 steel

The processing methods for a kind of slender,thin-walled tubular parts