Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

High Speed Tribology: Some Developments on Thermal Behaviors

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

The Relationships Between Tribological Behaviour and Heat-Transfer Capability of Ti6Al4V Alloys

Wear Rate, Frictional Temperature, and Energy Consumption of Steel 52100 with Different Microstructures During Sliding

Molecular Dynamics Simulation of Polycrystalline Metal under High Velocity Nanoscale Sliding

Effects of Fiber Diameter and Tribotest Conditions on Nonlubricated Frictional Behavior of a Microsized Metal Fiber

Modeling of contact temperatures and their influence on the tribological performance of PEEK and PTFE in a dual-pin-on-disk tribometer

Differences in Tribological Behaviors upon Switching Fixed and Moving Materials of Tribo-pairs including Metal and Polymer

Dry Friction Characteristics of Ti-6Al-4V Alloy under High Sliding Velocity

The effect of temperature on the tribological characteristics of high speed steels under conditions of friction without lubricant on the structural steel 30HGSA

Influence of Groove Surface Texture on Temperature Rise under Dry Sliding Friction

Experimental and Finite Element Analysis of Frictional Heat Distribution during Sliding Friction

Effect of thermorheological properties on tribological behaviors of lubricating grease

Tribological Behavior and Wear Mechanism of Cu-SiO2 Sintered Composite under Different Sliding Speeds

Tribological Behaviors of Several Polymer–polymer Sliding Combinations under Dry Friction and Oil-Lubricated Conditions

The Influence of Temperature and Load on Dry Sliding Wear and Friction Property of Low Metallic Friction Material

Improving the tribological performance of CFRPTFE at elevated temperature by sliding against Ti-TiCx/DLC film

Effect of Different Atmospheres on Dry Friction Behavior of Steel Sliding Against Brass at High Speed

High temperature solid/liquid lubrication behaviours of DLC films

Effect of Relative Humidity on the Tribological/conductive Properties of Cu/Cu Rolling Contact Pairs

Tribological behavior of heat treated AISI 6150 steel