Abstract:To increase the maximum internal pressure that a polyethylene (PE) pipe can withstand, a novel rotational shear system (RSS) was constructed in this study to fabricate PE pipes with enhanced hoop strength by applying hoop shear on the pipes using a rotational mandrel. The microstructure and morphology with the influences of melt plasticizing temperature on PE pipes processing under rotational shear were investigated indirectly using small-angle X-ray scattering and wide-angle X-ray diffraction (SAXS/WAXD) measurements. In the SAXS patterns, equatorial streaks and meridional scattering peaks were clearly observed in all three samples prepared at different melt plasticizing temperatures, 215, 235, and 255 °C. Their presence indicated that shish–kebab crystals form in rotational shear. Compared to those at the low melt temperature, the increase in the melt temperature enhanced the amount and the dimensions of shish formed. However, the shish also relaxed faster at the high melt temperature. This behavior was attributed to the enhancement of the molecular chain's athletic ability. The hoop tensile strength and the heat resistance of the pipes peaked at the melt plasticizing temperature of 235 °C, 75.2 MPa, 102.4 °C, up 1 MPa, 0.2 °C (compared to the 215 °C) and 7.8 MPa, 3.2 °C (compared to the 255 °C). The axial strength increased with an increase of melt plasticizing temperature. However, the increase of melt plasticizing temperature worsens the inherent good tensile toughness of PE100 pipes as the axial elongation at break decreases.This article has not yet been cited by other publications.

Effect of Rotating and Drawing Speeds on the Structure and Properties of Polyethylene Pipes Prepared by Rotation Extrusion

Effect of the inner wall cooling rate on the structure and properties of a polyethylene pipe extruded at a high rotation speed

STRUCTURE AND PERFORMANCE OF POLYETHYLENE PIPE PREPARED BY MANDREL AND DIE OPPOSITE ROTATION EXTRUSION

The Effect of Rotational Extrusion on the Structure and Properties of HDPE Pipes

Effect of Die Temperature on Morphology and Performance of Polyethylene Pipe Prepared Via Mandrel Rotation Extrusion

Control of Rotation Extrusion over Shish‐kebab Crystal Alignment in Polyethylene Pipe and Its Effect on the Pipe's Crack Resistance

Morphology and Property of Polyethylene Pipe Extruded at the Low Mandrel Rotation

Effect of rotation extrusion and molecular weight on ductile failure of polyethylene pipes under hydrostatic pressure

Structure and Performance of Polybutene-1 Pipes Produced Via Mandrel Rotation Extrusion

Role of Ultrahigh Molecular Weight Polyethylene During Rotation Extrusion of Polyethylene Pipe

The role of mandrel rotation speed on morphology and mechanical properties of polyethylene pipes produced by rotational shear

Enhanced effect of thermal expansion process in rotational shear technology for high performance HDPE pipes

Effect of mandrel rotation speed on morphology and mechanical properties of polypropylene pipes produced by rotational shear

Effect of the Mandrel Rotation Speed and Inner Wall Cooling Rate on the Performance and Structure of Polypropylene Block-Copolymer Pipe

Structure and Self-Reinforcing Mechanism of Biaxially Oriented Polyethylene Pipes Produced by Solid Phase Die Drawing

The effect of high-temperature annealing on thermal properties and morphology of polyethylene pipes prepared by rotational shear

High-density Polyethylene Pipe with High Resistance to Slow Crack Growth Prepared Via Rotation Extrusion

Preparation of High-Performance Polyethylene Tubes under the Coexistence of Silicone Cross-Linked Polyethylene and Rotation Extrusion

Role of Melt Plasticizing Temperature in Morphology and Properties of PE100 Pipes Prepared by a Rotational Shear System

Effect of Different Shear Modes on Morphology and Mechanical Properties of Polypropylene Pipes Produced by Rotational Shear

Effect of annular expansion pipe extruder head on mechanical properties of pipes