Abstract:For the purpose of reducing weight of steel parts, save raw materials and keep or even improve safety standards, the development of advanced high strength steels is increasingly demanded in the automotive industry and engineering applications. We have proposed a novel heat treatment (quenching-partitioning-austempering treatment, Q-P-A) to obtain steel parts with high strength and good ductility. The Q-P-A process is intended to produce microstructure consisted of carbon-depleted martensite, carbon-enriched retained austenite and nanostructured bainite. Quenching(Q) treatment fabricates mixed microstructure of carbon-supersaturated martensite and certain amounts of untransformed austenite. Partitioning(P) thermal treatment accomplishes fully diffusing of carbon from the supersaturated martensite phase to the untransformed austenite phase and enriching the amount of carbon in untransformed austenite. Further low-temperature austempering(A) process induces incredible thin bainite from the carbon-enriched untransformed austenite. A study of the microstructure and mechanical properties of 50SiMnNiNb steel subjected to the novel Q-P-A treatment is presented. Microstructure is assessed by optical microscope(OM), field emission scanning electron microscope(FESEM) and transmission electron microscope(TEM), and the corresponding mechanical properties are measured. The experimental results indicate that attractive mechanical properties of steels during the Q-P-A process are attributed to the complex multi-phase structure. Slender plates of bainite with 20-40 nm thick are generated in the medium carbon steel. Meanwhile, with increasing of the volume fraction of nanostructured bainite, yield strength of steel parts is increased with little degradation of ultimate tensile strength. In this paper, a novel quenching-partitioning-austempering heat treatment is proposed, and the attractive mechanical properties of steels are obtained during the Q-P-A process.

Application of Quenching-Partitioning-Tempering Process in Hot Rolled Plate Fabrication

Investigation on High Strength Hot-Rolled Plates by Quenching-Partitioning-Tempering Process Suitable for Engineering

Quenching-Partitioning-Tempering Process and Its Engineering Feasibility of 900 MPa Grade Hot-Rolled Plate

Development And Application Of Multicycle Quenching-Partitioning-Tempering Process

Quenching-partitioning-tempering and Multicycle Quenching-partioning-tempering Processes

Characterization of Microstructure and Mechanical Properties of a Nb-Microalloyed Steel after Quenching-Partitioning-Tempering Process

Study of a Novel Ultra-High Strength Steel with Adequate Ductility and Toughness by Quenching-Partitioning-Tempering Process

A Brief Introduction to Quenching-Partitioning-tempering(q-p-t) Process

Strengthening and toughening mechanisms of quenching–partitioning–tempering (Q–P–T) steels

Quenching-Partitioning-Tempering(Precipitation)(Q-P-T) Process for Ultra-high Strength Steel

High strength-elongation product of Nb-microalloyed low-carbon steel by a novel quenching–partitioning–tempering process

Microstructure and Mechanical Properties of A Nb-Microalloyed Medium Carbon Steel Treated by Quenching-Partitioning Process

The Microstructural design and control of ultrahigh strength-ductility martensitic steels based on a novel quenching-partitioning-tempering process

High Strength Ductility Steels Treated by Novel Quenching–partitioning–tempering Process

Development of Multi-Cycle Quenching–partitioning–tempering Process and Its Applications in Engineering

Enhancement of the mechanical properties of a Nb-microalloyed advanced high-strength steel treated by quenching–partitioning–tempering process

A novel microstructural design and heat treatment technique based on gradient control of carbon partitioning between austenite and martensite for high strength steels

The investigation of ultra-high strength steel by quenching-partitioning- tempering (Q-P-T) process

Microstructure and Mechanical Properties of 50simnninb Steel by A Novel Quenching-Partitioning-Austempering Heat Treatment

Property and Microstructure of a Novel Q-P-T Steel

Ultra-high Strength Steel Treated by Using Quenching–Partitioning–Tempering Process