Abstract:We describe the modeling of magnetoelectric (ME) effect in the plate-type Terfenol-D/PZT laminate composite by introducing a newly proposed interface coupling factor into the equivalent circuit model, aiming at providing a guidance for designing, fabricating and using the ME laminate composite based devices, such as current sensor, magnetic sensor, energy harvester, and wireless energy transfer system. Considering that the strains of the magnetostrictive and piezoelectric layers are not equal in actual operation due to the epoxy resin adhesive bonding condition, the equivalent circuit models of magnetostrictive and piezoelectric layers are created based on the constitutive equation and the equation of motion, respectively. An interface coupling factor k(c) is introduced which physically reflects the strain transfer condition between the magnetostrictive and piezoelectric phases. Specifically, the respective equivalent circuit models of magnetostrictive and piezoelectric layers are combined with an ideal transformer whose turn-ratio is just the interface coupling factor. Furthermore, the theoretical expressions containing k(c) for the longitudinal ME voltage coefficient alpha(v) and the optimum thickness ratio n(optim) to which the maximum ME voltage coefficient corresponds are derived from the modified equivalent circuit model of ME laminate, where the interface coupling factor acts as an ideal transformer. To explore the influence of mechanical load on the interface coupling factor k(c), two sets of weights, i.e., 100 g and 500 g, are placed on the top of the ME laminates, each with the same thickness ratio n in the sample fabrication for comparison. A total of 12 L-T mode plate-type ME laminate samples with different-thickness configurations are fabricated. The interface coupling factors determined from the measured alpha(v) and the DC bias magnetic field H-bias are 0.15 for 500 g pre-mechanical load and 0.10 for 100 g pre-mechanical load, respectively. Furthermore, the measured optimum thickness ratios are 0.57 for k(c) = 0 : 1 5 and 0.50 for k(c) = 0 : 1 0, respectively. Both the measured ME voltage coefficient alpha(v) and optimum thickness ratio containing k(c) agree well with the corresponding theoretical predictions. The relationship between the optimum thickness ratios under two different mechanical loads remains unchanged, i.e., the measured optimum thickness ratio for k(c) = 0 : 1 5 is larger than for k(c) = 0.10. The experimental results verify the reasonability and correctness of the introduction of k(c) in the modified equivalent circuit model. The possible reasons for different interface coupling factors under different loads are also qualitatively discussed in this paper.

Electromagnetic Equivalent Model for Phase Conjugate Mirror Based on the Utilization of Left-Handed Material

Orbital angular momentum (OAM) generation by composite PEC-PMC metasurfaces in microwave regime

The Effects of Reflection Phase Shift on the Optical Properties of a Micro-Opto-electro-mechanical System Fabry–Perot Tunable Filter

Phase compensating effect in left-handed materials

Hybrid Electromagnetic Boundary for Cavity Resonance Suppression

Analytical Model of Electromagnetic Performance for Permanent-Magnet Vernier Machines Using Nonlinear Exact Conformal Model

Reconfigurable phase-change metasurfaces from efficient wavefront manipulation to perfect absorption

Reflection and Phase of Left-Handed Metamaterials at Microwave Frequencies

Design and analysis of a kind of mushroom-like left-handed material

Mechanics of Hemispherical Electronics

TEM-wave propagation in a coaxial waveguide with impedance-matched RHM to LHM transition

Harmonic-Modulated Nonlinear Metasurface Based On Generalized Phase Conjugation Principle

Toward accurate thermal modeling of phase change material based photonic devices

Molding Reflection From Metamaterials Based On Magnetic Surface Plasmons

Simultaneous normal and parallel incidence planar left-handed metamaterial

Focusing and Phase Compensation of Paraxial Beams by a Left-Handed Material Slab

Equivalent circuit model for plate type magnetoelectric laminate composite considering an interface coupling factor

Effective Polarization Control of Metallic Planar Chiral Metamaterials with Complementary Rosette Pattern Fabricated by Nanoimprint Lithography

Comparisons Of Negative Refraction In Left-Handed Materials And Photonic Crystals

Novel Efficient Discontinuous Galerkin Time-Domain Modeling of Dispersive Chiral Metamaterials via Media Homogenization

A scheme for simulating multi-level phase change photonics materials