Abstract:Forming limit diagrams (FLDs) are very important in predicting the behavior of the sheet. Therefore, predicting and drawing these diagrams by theoretical and experimental methods has been one of the main objectives of this paper. In this paper, the formability behavior of 5083 aluminum sheet was investigated by considering the strain hardening behavior. Tensile tests has performed in seven directions 0°, 15°, 30°, 45°, 60°, 75° and 90° from the rolling direction due to identify and calibrate coefficients of BBC2008 advanced yield criteria. The yield stresses was defined in the plane strain mode, also the anisotropy coefficients and the appropriate error function were extracted and then the relationships of the plane strain yield stress were added to the error function. The error function was optimized using Genetic Algorithm and limit strains were calculated using yield coefficients. The results showed that if the strain hardening exponent increases by 0.1, the limit strains increase by 30 to 40%. Also the results showed that the initial imperfection factor ( 𝑓 0 ) has a great effect on determining the FLD and with a very small change, it has a great effect on the FLD; So that by increasing this factor to about 0.016, the values of the limit strains are almost doubled. Using the results of this paper and having sheet properties such as yield strengths and anisotropy coefficients and proper selection of yield criteria, the FLD of different sheets to be theoretically determined with acceptable accuracy. [1] Plastic Instability and Fracture in Sheet Stretched over Rigid Punches. [2] Application of strain analysis to sheet metal forming problems in the press shop. [3] On discontinuous plastic states, with special reference to localized necking in thin sheets. [4] Limit strains in the processes of stretch-forming sheet metal. [5] The influence of strain-path changes on forming limit diagrams of A1 6111 T4. [6] Investigation of formability of low carbon steel sheets by forming limit diagrams. [7] Theoretical determination of forming limit diagram for steel, brass and aluminum alloy sheets. [8] Experimental and numerical evaluation of forming limit diagram for Ti6Al4V titanium and Al6061-T6 aluminum alloys sheets. [9] Experimental and numerical analysis of forming limit diagram (FLD) and forming limit stress diagram (FLSD). [10] Forming limit and fracture mechanism of ferritic stainless steel sheets. [11] Calculation of forming limit diagrams using Hill's 1993 yield criterion. [12] The effects of anisotropic yield functions and their material parameters on prediction of forming limit diagrams. [13] The Effect of Advanced BBC2003, Yld2004 and BBC2008 Yield Criteria on FLDs Based on MK, Swift's and Hill's Models. [14] An experimental and theoretical investigation for determination of yield criteria parameters... [15] The forming limit curve for multiphase advanced high strength steels... [16] Forming limits of dual phase steels using crystal plasticity in conjunction with MK approach. [17] Prediction of FLD for sheet metal by considering through-thickness shear stresses. [18] Investigation on the effective range of the through thickness shear stress... [19] Controlling factors of forming limit curve: A review. [20] Crystal plasticity finite element – Marciniak-Kuczynski approach with surface roughening effect... [21] Plane stress yield criterion for highly anisotropicsheet metals. [22] Techniques of measurement of body composition Part II. [23] An improved analytical description of orthotropy in metallic sheets. [24] A study of microstructure and tribological properties of Al 5083 MMC processed by direct extrusion. [25] A novel and simple method for the measurement of plane strain work hardening.

Application of Hill's New Yield Theory to Sheet Metal Forming—part I. Hill's 1979 Criterion and Its Application to Predicting Sheet Forming Limit

Applications of the Hill 1948 Yield Criterion Development, Performance Evaluation and Comparison for Describing the Behaviour of Different CRCA Grades

Suitability of some ductile fracture criteria and yield criteria in forming limit prediction

Explicit Analysis of Transversely Anisotropic and Axisymmetric Sheet Metal Forming Process Using 6- Component Barlat Yield Function

Application of anisotropic constitutive equations to numerical simulation of sheet forming

Effects of Anisotropic Yield Criteria on the Prediction of Sheet Metal Forming of Aluminum Alloy Sheet

REVIEW ON DEVELOPMENT AND EXPERIMENTAL VALIDATION FOR ANISOTROPIC YIELD CRITERIONS

Constitutive Model of Hydroforming and Its Numerical Validation Based on Three-Dimensional Hill'48 Yield Criterion

Forming Limit Calculation Based on the M-K Model with Yld96 Yield Function

Constitutive modeling based on non-associated flow rule for anisotropic sheet metals forming

Bifurcation Analysis of Forming Limits for an Orthotropic Sheet Metal

Limitation analysis of the Hill48 yield model and establishment of its modified model for planar plastic anisotropy

Modeling stress anisotropy, strength differential, and anisotropic hardening by coupling quadratic and stress-invariant-based yield functions under non-associated flow rule

Experimental and Theoretical Study of Formability Behavior of Aluminum Alloy 5083 Sheet for Determination of Advanced Anisotropic Yield Criteria Coefficient and Prediction of Forming Limit Diagram

A Normalized Stress Invariant-Based Yield Criterion: Modeling and Validation

Fracture-based forming limit criteria for anisotropic materials in sheet metal forming

Proposal and application of a new yield criterion for metal plastic deformation

Prediction of Forming Limits for Anisotropic Materials with Nonlinear Strain Paths by an Instability Approach

Sheet metal forming limits under stretch-bending with anisotropic hardening

A new anisotropic-asymmetric yield criterion covering wider stress states in sheet metal forming

Construction of the Hill48 and Yld89 for Auto-body Steel Sheets Considering the Strain Rate