Abstract:Sheet metals usually exhibit a certain degree of plastic anisotropy because of the rolling effect. To characterize the anisotropic behavior in simulations related to large deformation, strain-rate independent phenomenological models are frequently used in quasi-static conditions. Two functions are generally included in such a model, i.e. the yield function and the plastic potential. The former limits the stress state within the yield surface while the latter determines the direction of the plastic strain increment. Traditional plasticity models mostly assume associated flow rule, in which the two functions mentioned above are identical. With the enhanced demand of accuracy, the forms of the associated models become too complex with more and more parameters to achieve an easy calibration procedure. Alternatively, in the past decade the non-associated models were increasingly used for sheet metals. Separate functions for the two aspects of plasticity lead to efficient characterization and convenient calibration. In numerical study of dynamic loading cases, how to characterize strain-rate dependence of plasticity is an important issue. Some visco-plastic models were developed to take the rate effect into account, e.g. Johnson-Cook and Cowper-Symonds models, where the isotropic J2 flow theory was commonly used. However, when the material is severely anisotropic, this approach is very likely to be insufficient, and a model including both anisotropy and rate dependence would be needed. Extending a non-associated anisotropic model to be rate-dependent is a promising approach which has not been published in open literature to the best knowledge of the authors. Objective of the present study is to develop an applicable model for characterizing dynamic mechanical behavior of a typical high-strength steel sheet. Two steps are performed. The material is investigated under quasi-static loading firstly. Tensile test results show an obvious anisotropy which cannot be described by traditional associated models. So the non-associated Hill48 model is chosen and calibrated. Accuracy of the model is verified by a quasi-static punching test. Thereafter the dynamic material properties are obtained by conducting tensile tests at quite a few strain-rate levels covering 0.0004–1200s−1. To characterize the positive strain-rate effect in strength, the non-associated Hill48 model is extended to be visco-plastic after checking two rate-dependence formulations in existing isotropic models. With implementing the extended model into a user subroutine of ABAQUS/explicit, simulations of the dynamic tension tests are run and compared to the real experiments. A good agreement between the simulated and the experimental result is achieved using the VUMAT.

Strength modeling of sheet metals from shear to plane strain tension

A general yield function with differential and anisotropic hardening for strength modelling under various stress states with non-associated flow rule

Modeling stress anisotropy, strength differential, and anisotropic hardening by coupling quadratic and stress-invariant-based yield functions under non-associated flow rule

An Experimental Methodology to Characterize the Plasticity of Sheet Metals from Uniaxial to Plane Strain Tension

A new anisotropic-asymmetric yield criterion covering wider stress states in sheet metal forming

Modeling of Eyld2000-2d Anisotropic Yield Criterion Considering Strength Differential Effect and Analysis of Optimal Calibration Strategy

A non-quadratic pressure-sensitive constitutive model under non-associated flow rule with anisotropic hardening: Modeling and validation

Characterization and modelling of evolving plasticity behaviour up to fracture for FCC and BCC metals

A user-friendly anisotropic ductile fracture criterion for sheet metal under proportional loading

Extension of Non-Associated Hill48 Model for Characterizing Dynamic Mechanical Behavior of A Typical High-Strength Steel Sheet

Experimental Methodology for Obtaining the Flow Curve of Sheet Materials in a Wide Range of Strains

Constitutive modeling based on non-associated flow rule for anisotropic sheet metals forming

Large strain flow curve identification for sheet metals under complex stress states

Lode-dependent Yld91 function for anisotropic-asymmetric hardening modeling of metals under non-associated flow rule

Experimental Characterization and Yield Strength Model for Process-Structure-Property of Selective Laser Melted 316L

On the flat punch hole expansion test of sheet metals: Mechanics of deformation and evaluation of anisotropic plasticity models

Lode-dependent anisotropic-asymmetric yield function for isotropic and anisotropic hardening of pressure-insensitive materials. Part I: Quadratic function under non-associated flow rule

User-friendly anisotropic hardening function with non-associated flow rule under the proportional loadings for BCC and FCC metals

A Physical-Based Plane Stress Constitutive Model for High Strength AA7075 under Hot Forming Conditions

Plastic anisotropy of sheet metals under plane strain loading: A novel non-associated constitutive model based on fourth-order polynomial functions

A method for the simultaneous identification of anisotropic yield and hardening constitutive parameters for sheet metal forming