Abstract:The electroplated diamond wire saw is a crucial tool for cutting semiconductor materials such as silicon ingots and sapphire. The nickel (Ni)-coated diamond serves as an essential abrasive in the production of electroplated wire saws. Nevertheless, producing Ni-coated diamonds necessitates the use of the precious metal palladium as a catalyst. Moreover, Ni-coated diamonds are prone to detachment from the wire saw during cutting, since no chemical bond is formed between Ni and the diamond. To address these issues, we proposed the production of electroplated diamond wire saws using Ni/titanium (Ti)-coated diamonds. The vacuum slow evaporation technology had been used to apply a uniform Ti coating on the diamond micro-powder (8 μm), which firmly bonded to the diamond through the interfacial product TiC. The Ti-coated diamonds exhibited surface activity, allowing direct electroless plating of the Ni coating without palladium. At an overpotential of −0.7 V, the current densities in the composite electroplating bath were − 0.026 A/cm2 (Ni/Ti-coated diamond) and − 0.018 A/cm2 (Ni-coated diamond). Additionally, electrochemical impedance spectroscopy showed that the charge transfer resistances were 3.72 Ω and 4.45 Ω, respectively. Thus, Ni/Ti-coated diamonds enhanced the composite electroplating reaction. The Ni/Ti-coated diamond wire saws also showed superior abrasive density per unit length. These improvements were ascribed to the formation of Ni and Ti coatings on the diamond surface. Moreover, the Ni/Ti-coated diamond wire saw exhibited greater resistance to detachment in cutting trials, allowing at least a twofold increase in diamond exposure. Utilizing Ni/Ti-coated diamond micro-powder as an abrasive in the electroplating of diamond wire saws offers a cost-effective and efficiency-enhancing solution for manufacturers, potentially extending the wire saw's lifespan. This development is poised to drive advancements in the processing technology of hard and brittle materials.

Electroless Plating Composite Coatings of Ni-Ti-Re on the Surface of Diamond

Diamond particles-reinforced Ni-based composite coating on Ti6Al4V alloy: Microstructure, mechanical, dynamic impact and dry-sliding tribological properties

Influence on (Ni-P) Electroless Composite Plating with Carbon Nanotubes

Production of Cu/Diamond Composite Coatings and Their Selected Properties

A novel strategy for improving the wear resistance of electrodeposited Ni-diamond composite coatings by diamond surface morphology modification

Effect of Particle Concentration on the Microstructure and Properties of Electrodeposited Nickel–Diamond Composite Coatings

Preparation and tribological properties of novel cold–sprayed Ti–diamond composite coating

Effect of variations in Ni-W molar ratio on the microstructure, mechanical properties and tribology of electrodeposited Ni-W/diamond composite coatings

Electrodeposition of Ni-P composite coatings: A review

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Electrodeposition of RE-Ni-Fe-P-PTFE Composite Coating

Preparation of Ti-coated Diamond Particles by Microwave Heating

Preparation of the Ni/Ti-coated diamond micro-powder for electroplated diamond wire saws using vacuum slow evaporation technology combined with the palladium-free electroless plating

The Microstructure and Wear Properties of Diamond Composite Coatings on TC4 Made by Induction Brazing

A Ni/Surface-Modified Diamond Composite Electroplating Coating on Superelastic NiTi Alloy As Potential Dental Bur Design

Facile electroless copper plating on diamond particles without conventional sensitization and activation

Comparative study on the properties and microscopic mechanism of Ti coating and W coating diamond-copper composites

Tungsten-coated Diamond Powders Prepared by Microwave-Heating Salt-Bath Plating

Study on Ni-P-nanoTiN Electroless Composite Coating

Effect of Nanodiamond Content in the Plating Solution on the Corrosion Resistance of Nickel–Nanodiamond Composite Coatings Prepared on Annealed 45 Carbon Steel

Introduction of heavy micro titanium carbide particles into Zn‐Ni coatings on steel during in‐situ brush electroplating