Development of Resistive Trays for Solid-Containing and Pluging System

Han Renyu,Geng Jiao,Zhang Feng,Zhang Zhibing

DOI: https://doi.org/10.3969/j.issn.1002-154X.2006.03.001

2006-01-01

Abstract:The mechanism of solid deposition and the characteristics of liquid flow on the tray were studied.A series of novel resistive trays for solid-containing,pluging and viscous system were also developed.

What problem does this paper attempt to address?

Study on the Fluid Dynamics Characteristics of Stirring-Box Tray

郭敏强,周政,张志炳

DOI: https://doi.org/10.3969/j.issn.1005-9954.2003.01.001

2003-01-01

Abstract:A patented tray called stirring-box tray has been developed and tested. A number of specially designed stirring-boxes are fixed over the collective sieve holes. The fluid mechanics characteristics of the tray,i.e. pressure drop, weeping, entrainment and liquid height in the downcomer, are determined on a test rig with 1000mm by air-water system at an atmospheric pressure. The experimental results are compared with those of the traditional sieve tray. It indicates that the stirring-box tray has the advantage of lower entrainment and bigger flux. The correlations for calculating the pressure drop of the stirring-box tray are derived from the experimental data. In addition, the liquid stream on the tray bed is pushed by the spurting liquid from the mouth of stirring-box with the same direction of liquid flow on the tray,which can reduce the liquid eddy and backmixing. Theoretically, being well mixed in the stirring-box with the liquid-phase, the vapor-phase leaving the stirring-box will approximately reach equilibrium with the liquid flowing from the box.As a result, the mass transfer efficiency of the tray might increase greatly.
Experimental study of two phase flow characteristics on the dual-flow tray

jiajia zhang,yifei wang,guangsuo yu,xiajun mao,fuchen wang

DOI: https://doi.org/10.1016/j.cherd.2015.06.018

IF: 4.119

2015-01-01

Chemical Engineering Research and Design

Abstract:•Hydrodynamic behavior of a new type of dual-flow fixed valve tray was studied.•Four main hydrodynamic regimes are distinguished at different gas/liquid load.•Geometry of trays was investigated and compared with each other.•A characteristic parameter named the fraction of holes passing gas is defined and deduced.
New Method for Designing an Energy-Saving Tray and Its Hydrodynamic Aspects: Temperature Distribution and Efficiency of Deflected Tray-95

Z Zheng,Cl Ying,Bz Zhi

DOI: https://doi.org/10.1021/ie020720+

2003-01-01

Industrial & Engineering Chemistry Research

Abstract:A series of well-designed deflectors were placed on the tray-95 to improve the flow pattern. A phenomenon of multiple plug flow was observed in each liquid flow channel between two deflectors on the deflected tray-95. In compliance with the theoretical prediction, temperature profiles of the liquid layer on the tray were measured both vertically and horizontally by resistive thermal detectors. An oxygen desorption experiment was carried out, and the oxygen concentrations in the inlet and outlet liquids were detected by iodometry. Then the liquid-phase Murphree tray efficiencies (E-ML) were calculated. The results show that the well-designed and well-placed deflectors can obviously increase the tray efficiency by almost 30% under the same operating conditions.
Study on the Gas-liquid Performance of the Compound Tray

聂勇,计建炳,徐之超,谭天恩

DOI: https://doi.org/10.3321/j.issn:1003-9015.2003.04.003

2003-01-01

Abstract:The gas-liquid performance of the compound tray with free area 20% and 25% respectively was investigated by multi-path conductometer. All runs were carried out in a 500mm diameter column with water-air system. Three states such as liquid flowing, gas flowing, and liquid blocked for the holes were put forward and the corresponding mechanism was clarified. The effects of factors including F parameter, liquid flow rate, and tray fractional free area on the holes ratio of three flowing state were studied, and the relations of the real gas velocity through the holes and the flooding point were discussed. Results show that gas flow ratio increases with the increase of F parameter and the decrease of liquid flow rate and tray fractional free area. Liquid flow ratio is the inverse of gas flow ratio; liquid blocked ratio increases with the increase of tray fractional free area and the decrease of F parameter. The real gas velocity in the holes at flooding point is about 11ms-1 under certain tray fractional free area (20%, 25%) and liquid flowing rate (5~40 m3(m2h)-1), according to these data, the operating up limit of compound tray for other gas-liquid system can be reckoned.
A Kind of New Improved Vertical Sieve Tray I. Hydrodynamics

DU Dong-yun,FANG Yun-jin,XIAO Wen-de

DOI: https://doi.org/10.3969/j.issn.1006-3080.2000.03.009

2000-01-01

Abstract:New vertical sieve tray is a kind of new vaporliquid contact apparatus for heat or mass transfer such as distillation or absorption apparatus in the chemical industry. The contact structure comprises cylindrical walls surrounding gasflow openings in the trays and the wall is secured to the trays and has apertures at a lower portion thereof. A perforated cylinder and a cover are provided atop of the cylindrical wall. Liquid falling from a plate is blown up by the ascending gas or vapor to form vaporliquid mixing phase flow, and the flow is then inverted by a top cover and passes through holes of a vertically provided perforated plate to be separated into vapor and liquid. Vapor and liquid contact is performed during the vaporliquid mixing phase flow and while passing through the small holes of the performed plate. By the research on the hydrodynamics of several vertical sieve trays differing in the top structure, a new improved cap (turbination cap) is proposed. It has characteristics of lower pressure drop and lower entrainment. Its wet plate pressure drop related equation (multicover system) can be expressed as: h_t=2 047ρ_gρ_1u2__02g+0.81h_1
Research progress in development of high capacity trays

DING Meng-jun,WANG Cheng-xi

DOI: https://doi.org/10.3969/j.issn.1005-9954.2010.10.007

2010-01-01

Abstract:The recent development of high-capacity trays at home and abroad was summarized.Through the analysis of trays operation principle,two methods for increasing the capacity of tray were proposed.By grouping these high-capacity trays into two categories,the structures and features of which were presented.On this basis,some specific measures for development of high-capacity trays were summarized,and the prospect of high-capacity trays was discussed.
The fluid dynamic characteristics of the 95-type tray

李鹏,吴有庭,张志炳

DOI: https://doi.org/10.3321/j.issn:0469-5097.2000.04.017

2000-01-01

Abstract:The fluid dynamic characteristics of the new 95-type tray are investigated in a 1.0 m diameter test rig using the air-water system at atmospheric pressure. Experimental data of flow pattern, pressure drop, weeping and liquid height in the downcomer are obtained and analyzed, and the equations for calculating the tray pressure drop and the liquid height are derived from the experimental results. It shows that the pressure drop of the 95-type tray is lower than that of tradifional sieve tray. and the 95-type tray have the lower weeping curves character. The liquid flow pattern on the tray is almost changed into idea model.
Computational study for mass transfer on commercial multi-pass trays

ZHAO Dan,ZHANG Yan,GAO Xueying,Chunjiang Liu,YUAN Xigang

DOI: https://doi.org/10.3969/j.issn.0438-1157.2011.09.007

2011-01-01

Abstract:A two-dimensional pseudo single phase model is proposed to describe the flow and mass transfer phenomenon on a four-pass distillation tray with a diameter of 12.6 m by combination of computational fluid dynamics(CFD)and computational mass transfer(CMT)equations.The resistance and bubbling effect of the uprising gas phase are considered.The velocity profile and concentration distribution are calculated for the tray designed by traditional equal bubbling area method and for the modified tray under different operational conditions.For the traditional four-pass distillation tray,the liquid loading ratio(Q1/Q2)of 1.0 is first considered.Simulated results show that on its left-side tray there exists a recirculation region,which is in accord with the observations from industrial practice,and a large velocity difference between the arc-shaped region and the main flow region.These two factors account for the lower separation efficiency on the left-side tray compared with that on the right-side tray.Then the influence of Q1/Q2 on tray efficiency is investigated.Simulated results give an optimal Q1/Q2 around 0.8 in terms of tray efficiency.In order to optimize the tray configuration and improve the tray separation efficiency,a modified tray configuration is constructed by introducing several deflectors.The simulation is conducted under the same operational conditions as those for the traditional tray.Calculated results present much more uniform flow regime with the disappearance of recirculation phenomenon and the Murphree tray efficiency is increased by 4.53%—9.22%(Q1/Q2=[0.5,1.5]) compared with the traditional tray.With these deflectors, the optimal Q1/Q2 in terms of tray efficiency changes from 0.8 to 0.7,probably due to the much more uniform flow pattern at low Q1/Q2 as a result of deflectors.
Improvement of Fixed Valve Trays

N. A. Voynov,A. S. Frolov,N. Yu. Kozhukhova,A. V. Bogatkova

DOI: https://doi.org/10.1007/s10556-022-01106-z

2022-09-23

Chemical and Petroleum Engineering

Abstract:The results of a study of hydrodynamics and mass transfer on fixed valve trays are presented along with an improved valve-vortex contact device. The fields of liquid and gas velocities, as well as the structure of the gas content in the liquid layer on the tray, were established through experimental research and numerical simulation in the OpenFOAM program. The dependence between the amplitude of fluctuations of the mixture on the tray, on the gas flow rate for the presented contact devices, is obtained. The circulation flows of the liquid on the tray are established, the average surface diameter of the gas bubble is determined. Experimental data on the value of the mass transfer coefficient and efficiency are presented. It has been established that the valve-vortex tray has the highest efficiency and capacity for liquid and gas.

English Else
Computational Fluid Dynamics Modeling of Hydrodynamics of A New Type of Fixed Valve Tray

Xingang Li,Na Yang,Yongli Sun,Luhong Zhang,Xuegang Li,Bin Jiang

DOI: https://doi.org/10.1021/ie400408u

2014-01-01

Industrial & Engineering Chemistry Research

Abstract:A three-dimensional computational fluid dynamics (CFD) model was developed to predict the hydrodynamics of a new type of fixed valve tray. The model considered gas- and liquid-flow within the Eulerian framework in which both phases were treated as interpenetrating continuum having separate transport equations. Interphase momentum transfer term was employed for describing the interfacial forces between the two phases, and the related average gas hold-up was obtained via the regression equation from experiment data. Calculations were carried out using the commercial packages ANSYS CFX 12.0. Clear liquid height, gas hold-up, and gas and liquid velocity profiles were predicted for various combinations of weir height, gas, and liquid flow rates. The predicted clear liquid height was generally in good agreement with measurement. The information predicted by the CFD model can be used in the optimal design of industrial trays.
Research and development of two-liquid phase flow in micro-structured devices

Guangsheng Luo,XU Jian-hong,Shaowei Li,WANG Yu-jun,WANG Jia-ding

2006-01-01

Abstract:The different flow patterns of liquid-liquid two-phase in micro-structured devices are systematically introduced and analyzed,and the two-phase flow characteristics and mixing performance of liquid-liquid systems in different flow patterns are reviewed.On that base,the developing prospects of micro-structured devices in liquid-liquid two-phase reactions and separation processes are explored,and the main directions of this research area are pointed out.
HYDRODYNAMICS OF PLURAL TRAY (Ⅰ) EFFECT OF HOLE DIAMETER AND FREE AREA OF PLURAL TRAY ON HYDRODYNAMIC PROPERTIES

杜冬云,王军,方云进,肖文德,陆晓华

DOI: https://doi.org/10.3321/j.issn:0438-1157.2002.07.006

2002-01-01

Abstract:As a large equipment used in flue gas desulfuration,Plural Tray,which operates in the spray regime and consists of large-holed sieve tray and structured packing,has been developed.Hydrodynamics of such new sieve tray is studied in this paper.The experiments are accomplished in a cold model column with diameter of 400?mm.The effect of hole diameter and free area of Plural Tray on the hydrodynamic properties is studied.The larger the hole diameter is,the more the wet tray pressure drop is;the more the free area is,the worse the operating flexibility is.As a result,Plural Tray has the characteristics of lower resistence,little entrainment and big upper limit velocity of operation.
Flow regimes and pressure drop of a composite tridimensional rotational flow sieve tray under concurrent gas‐liquid flow

Shaofeng Zhang,Bingfang Liu,Hongkai Wang,Yan Liu,Dewu Wang,Meng Tang,Shijie Dai

DOI: https://doi.org/10.1002/aic.17754

IF: 4.167

2022-05-18

AIChE Journal

Abstract:A composite tridimensional rotational flow sieve tray (CTRST) is proposed. The flow patterns of CTRST were recognized visually, combined with the standard deviation of the pressure difference. In the TRST area of the internal packing‐type tray, the membrane‐drip column and foam‐embolic flow is present, while bubbly and milk froth‐ribbon flow is present in the packing area of the external packing‐type tray. The effect of the tray structure parameters on the pressure drop under co‐current flow was investigated. The dry and wet pressure drop is within 160 and 900 Pa, respectively. Under the same structural parameters, the pressure drop of the internal packing‐type tray was higher than that of the external packing‐type tray. The flow characteristics of the standard tray under the countercurrent flow were compared. The CTRST was found to be more suitable for co‐current flow. A prediction model pressure drop under co‐current was established with an error of 15.5%.

engineering, chemical
Interfacial Area on Valve Trays

Yinchun LIANG,Zheng ZHOU,Zhibing ZHANG

DOI: https://doi.org/10.3321/j.issn:0438-1157.2007.05.028

2007-01-01

Abstract:The vapor-liquid contact and interfacial area on the valve tray were investigated on the basis of the mechanism of bubble deformation and breakage in the turbulent liquid.A mathematical model was proposed to compute the interfacial area on the valve tray.This model was capable of comparing the effects of the different valve configurations on the interfacial area.Based on the study,a new type valve,called guided rhombic valve(GRV),was designed and tested on a test rig with a column inner diameter of 1000 mm.The results showed that the gas-liquid interfacial area of GRV could be remarkably increased.
Research Development of Ceramics Slurry in the Wet Forming Process

ZHANG Yun-long,ZHANG Yu-min,ZHAO Xiao-jing,HAN Jie-cai

DOI: https://doi.org/10.3969/j.issn.1004-244x.2007.01.020

2007-01-01

Abstract:This paper summarizes the aspects of dispersion mechanisms of ceramics powder,the main influencing factors of ceramics slurry dispersion and recent development of research.It focuses on many influencing factors of ceramics slurry for stable dispersion,such as material property of ceramics powders,pre-treatment process and additives.It also points out the development trend of the wet forming process.
Dispersion of lateral and axial solids in a cocurrent downflow circulating fluidized bed

Fei Wei,Zhanwen Wang,Yong Jin,Zhiqing Yu,Wei Chen

DOI: https://doi.org/10.1016/0032-5910(94)02854-0

IF: 5.64

1994-01-01

Powder Technology

Abstract:A unique phosphor tracer technique has been developed that measures the solids tracer concentration with time at different radial and axial positions within the cocurrent downflow circulating fluidized bed with a 140 mm inner diameter. Solids mixing is described by a proposed two-dimensional dispersed plug-flow model. The radial and axial dispersion coefficients under various operating conditions were determined from the experimental values of tracer concentration versus time. On the basis of these results, correlations with the bed voidage and Reynolds number are proposed.
Study on vapor-rise-up through hanging downcomers

Yumin Li,Xiaomei Yu,Ping Chen,Jianbin Ji

DOI: https://doi.org/10.1016/j.cherd.2008.01.010

IF: 4.119

2008-01-01

Chemical Engineering Research and Design

Abstract:A common problem in high capacity trays is the difficulty of establishing a liquid seal of hanging or truncated downcomers since the hanging or truncated downcomers came out. When the downcomer seal is lost, the vapor rises up through the downcomer, which may cause tray instability and poor separation. For the downcomer unseal or vapor-rise-up, it was found that there exist two regimes of free vapor-rise-up regime and dynamic vapor-rise-up regime. The mechanism of free vapor-rise-up is lower liquid height than the tray pressure drop, whereas the mechanism of dynamic vapor-rise-up is the driving force of the tray pressure drop. Using the hydraulic model of dualflow tray, the vapor-rise-up model in dynamic regime was developed. The experiments were carried out in a 500mm-diameter transparent plexiglass column with air–water system. From the experimental data, the vapor-rise-up correlation was obtained. The free vapor-rise-up regime converts into dynamic regime with the increase of the vapor rate, and the transition point is a certain real velocity of rise-up vapor. For preventing the vapor-rise-up, a seal line is required. With the definition of the rise-up vapor being limited to a certain ratio of rise-up vapor rate to liquid rate, the seal line is qualitatively obtained from the vapor-rise-up model. The seal line has the minimum liquid rate, which is in accord with the seal line by Li et al. [Li, Y.M., Yu, X.M. and Yao, K.J., 2004, Dynamic seals on hanging downcomers. Chem Eng Res Des, 82: 1].
Development and Optimization of PZT Suspensions with High Solid Loading and Low Viscosity for Stereolithography-Based Additive Manufacturing

Yifei Jiao,Guifen Fan,Yongan Chen,Wanjun Yu,Feng Gong,Gang Liu,Jiaming Bai,Peng Zhou,Dongyang Zhang,Lining Sun

DOI: https://doi.org/10.1016/j.ceramint.2023.11.078

IF: 5.532

2024-01-01

Ceramics International

Abstract:Achieving synergy between high solid loading and low viscosity for ceramic suspensions a critical issue in the field of stereolithography. In this work, we successfully obtained a well-dispersed PZT suspension with high solid loading (55 vol.%) and low viscosity (3047.5 mPa s at 60 rpm) by adding appropriate amounts of dispersant (1 wt.% KOS110) and thickening agent (2 wt.% PEG300), providing a foundation for crack-free photosensitive lead zirconate titanate (PZT) samples. This work presented a simple approach for achieving synergy between the high solid loading and low viscosity of ceramic suspensions for stereolithography-based additive manufacturing.
High-Powered Adaptive Valve Tray

Jianbing Qian,Rongbing Qi,Shenlin Zhu

DOI: https://doi.org/10.1205/cherd.05067

IF: 4.119

2006-01-01

Chemical Engineering Research and Design

Abstract:Valve tray as one of the most important mass transfer and heat transfer equipments for vapour–liquid is widely used in distillation, absorption and extraction units of petroleum, chemical and environmental industry. In order to overcome the drawbacks such as malfunctions, scaling and coking of common Glitsch V1 trays, a new high-powered adaptive valve tray (HAV TH ), which integrates the high performance of fixed-valve tray and float-valve tray, is developed in this paper. The hydrodynamic and mass transfer performance of the HAV TH and V1 valve trays was experimentally studied with air–water– oxygen system in a φ 600 mm stainless steel column. The results show that the HAV TH tray possesses better characteristics than V1 tray on the hydrodynamics and mass transfer.
STUDY ON CHARACTERISTICS OF FRICTIONAL RESISTANCE OF A NOVEL DRY FRACTURING FLUID

LU You-Lian,ShuZhong Wang,SUN Xiao,BAI Yu,SONG Zhen-Yun,LI Zhi-Hang

2009-01-01

Journal of Engineering Thermophysics

Abstract:Whether we can correctly understand the frictional resistance characteristics of the modified dry fracturing fluid or not would influence the fracture technology's effective implementation. Hence,the frictional resistance of modified dry fracturing fluid in a down-hole condition has been studied on a large-scale flow-loop experiment system.The experimental results show that the frictional resistance coefficient of the modified dry fracturing fluid increases with the increase of pressure,temperature and the foam quality,decreases with the increase of flow velocity.The results also show that the temperature has a little activation on the frictional resistance coefficient.And we have established a correlation of the frictional resistance coefficicnt and the generalized Reynolds number with the average error of 9.19%.

Development of Resistive Trays for Solid-Containing and Pluging System

Study on the Fluid Dynamics Characteristics of Stirring-Box Tray

Experimental study of two phase flow characteristics on the dual-flow tray

New Method for Designing an Energy-Saving Tray and Its Hydrodynamic Aspects: Temperature Distribution and Efficiency of Deflected Tray-95

Study on the Gas-liquid Performance of the Compound Tray

A Kind of New Improved Vertical Sieve Tray I. Hydrodynamics

Research progress in development of high capacity trays

The fluid dynamic characteristics of the 95-type tray

Computational study for mass transfer on commercial multi-pass trays

Improvement of Fixed Valve Trays

Computational Fluid Dynamics Modeling of Hydrodynamics of A New Type of Fixed Valve Tray

Research and development of two-liquid phase flow in micro-structured devices

HYDRODYNAMICS OF PLURAL TRAY (Ⅰ) EFFECT OF HOLE DIAMETER AND FREE AREA OF PLURAL TRAY ON HYDRODYNAMIC PROPERTIES

Flow regimes and pressure drop of a composite tridimensional rotational flow sieve tray under concurrent gas‐liquid flow

Interfacial Area on Valve Trays

Research Development of Ceramics Slurry in the Wet Forming Process

Dispersion of lateral and axial solids in a cocurrent downflow circulating fluidized bed

Study on vapor-rise-up through hanging downcomers

Development and Optimization of PZT Suspensions with High Solid Loading and Low Viscosity for Stereolithography-Based Additive Manufacturing

High-Powered Adaptive Valve Tray

STUDY ON CHARACTERISTICS OF FRICTIONAL RESISTANCE OF A NOVEL DRY FRACTURING FLUID