Design of displacement measuring system using optical fibre sensor

Wang Bohai,Liu Jiansheng,Zhang Jiansong

DOI: https://doi.org/10.3969/j.issn.1002-7300.2006.04.074

2006-01-01

Abstract:In this paper, a displacement measuring system based on optical fibre sensor is designed. This system uses the CY8C29446 microcontroller and adopts dual channel processing technique to make it much smaller while maintains high performance.

What problem does this paper attempt to address?

Multimode-interference-effect-based all-fiber displacement sensing system for an orthopedic Ilizarov apparatus device.

Haidong Liang,Xianfan Wang,Ke Tian,Wenlei Yang,Elfed Lewis,Pengfei Wang

DOI: https://doi.org/10.1364/AO.58.003209

IF: 1.9

2019-01-01

Applied Optics

Abstract:The paper describes a multimode-interference-effect-based single-mode-multimode-sin -mode (SMS) fiber optic sensing system for wide-range displacement monitoring on an Ilizarov orthopedic external fixation device. Displacement measurement is implemented as the uniform extension of a spring, which is connected to an SMS optical fiber displacement sensor, allowing full displacement characterization. SMS fiber structures are used together with a macrobending-fiber-based interrogation system to measure temperature perturbation and hence eliminate its effect on the displacement measurement. Transmission spectra are measured, achieving a displacement measurement range of 110 mm with maximum sensitivity of -53 pm/mm and a resolution of 500 mu m. The all-fiber sensing system has facilitated a clinical device with a wide displacement range operating in real- time when attached to the Ilizarov apparatus. (C) 2019 Optical Society of America
Research of a Reflective Fiber-Optic Displacement Sensor with Intensity Compensation

HB Lu,T Xu,HY Yang,ZF Chen

DOI: https://doi.org/10.1117/12.403900

2000-01-01

Abstract:A reflective displacement sensor utilizing three fibers, one transmitting and two receiving with different core diameters, is described in this paper. On the basis of optical field distribution of multimode fiber, the intensity compensation mechanism of this sensor is analyzed in great detail, at the same time the displacement modulating functions and corresponding simulating carves are presented. Results show that this sensor can effectively compensate for variations in the source intensity, for losses in the optical fibers, and for variations in the reflectivity of the reflector surface.
A High-Resolution Displacement Sensor Based on a Grating Interferometer with the Phase Modulation Technique

Shuangshuang Zhao,Changlun Hou,Juan Zhang,Jian Bai,Guoguang Yang

DOI: https://doi.org/10.1088/0957-0233/23/10/105102

IF: 2.398

2012-01-01

Measurement Science and Technology

Abstract:A high-resolution displacement sensor based on a grating interferometer with the phase modulation technique is demonstrated in this paper. The grating interferometer is formed with a grating and a mirror, which is fixed on a piezoelectric translator to generate phase modulation. The detected signal is intensity-modulated and processed with a lock-in amplifier for demodulation. Experimental results show that this displacement sensor has a displacement sensitivity of 19.8 mV nm(-1) and a high-resolution displacement detection of 0.05 nm in the linear region.
Design and Operation of a Transmissive Plastic Fiber Optical Displacement Sensor

Yanxiang Chen,Yuhe Li,Xiaogen Hu

DOI: https://doi.org/10.1109/icoom.2012.6316332

2012-01-01

Abstract:Nowadays, optical fibers have a wide range of applications in the sensing field, especially in the displacement sensor. A Transmissive Plastic Fiber Optical Displacement Sensor (TPFODS) is designed, which achieves the displacement measurement by utilizing a cutting plate to modulate the light intensity. By performing an optical path simulation, the optical field distribution of the end of plastic optical fibers in different situations and the simulation curve of the relationship between the displacement and the light intensity are obtained. Furthermore, an experimental platform is set up, signal detection and processing circuit is designed. The experiments on light source stability and displacement measurement are conducted. The experimental results indicate the stability of the laser is poor and the error is up to ±1.7%. In this condition, two methods have been adopted to improve the system accuracy: 1. using the high-frequency modulated light source; 2. introducing a reference signal to reduce the error caused by the temperature-drift. After optimization, the stability error is reduced from ±1.7% to Error! Reference source not found. The measurement system has a good linearity in the range of 1000μm-3000μm, and the measurement error less than Error! Reference source not found.
A Novel Optical Fiber Displacement Measurement System

Kai Sen Guan,Yu He Li,Yan Xiang Chen,Yong Rong Qiu

DOI: https://doi.org/10.4028/www.scientific.net/amm.599-601.684

2014-01-01

Applied Mechanics and Materials

Abstract:In order to meet the displacement measurement’s need for high precision and large measuring range, a novel design of optical fiber displacement system is proposed. Optical fiber is applied to the displacement measurement field with its simple structure, light weight, cheap cost and high precision. A displacement measurement model based on transmissive optical fiber is established, and theoretical calculation and simulation are conducted to verify the accuracy of the model. Displacement measuring experiments are completed and the results show that the transmissive optical fiber displacement measurement system has high measuring accuracy with the relative error less than 0.2% over a large range.
Development of Wide Range Displacement Sensors Based on Polarized Light Detecting Technology

Xiaoping Lu,Wei Li,Yonggang Lin

IF: 0.6

2011-01-01

Optica Applicata

Abstract:A series of novel wide range displacement sensors based on polarized light detecting technology is presented. The sensors include a displacement-current comparator and a servo comparison displacement sensor. Special structures and technologies are introduced to the sensor systems to solve the optical problems, such as the nonlinearity, the light source drift etc., and realize wide range measurement. The designing, assembling, and testing results of the prototypes of sensors are described. The testing results of the prototypes show that the novel sensors based on polarized light detecting technology have good linearity, and wide range measuring ability.
Design of a Reflective Intensity Optical Fibre Bundle Displacement Sensor

Jia Binghui,Yu Jing,Feng Yong,Zhang Min,Li Gang

DOI: https://doi.org/10.11916/j.issn.1005-9113.18128

2020-01-01

Abstract:Optical fibre sensor has the advantages of small size, light weight, anti-electromagnetic interference, and high measurement accuracy, which has important applications in research and industrial production. To design an optical fibre displacement sensor ( OFBDS ) with simple structure and high measurement accuracy, the unified model of the commonly used OFBDS structures was proposed and the feasibility of the intensity-modulation of multi-structural optical fibre bundles was analysed based on the arrangement characteristics of the fibre bundle end-face. The intensity-modulation characteristic of different fibre bundles was analysed, and the single coil coaxial fibre bundle was chosen as the fibre probe in this study. The sensor hardware system was designed. Lastly, the calibration experiment, temperature interference experiment, changes of measured plane surface area, and the dynamic experiment were conducted. Results showed that the sensor linear measurement range was about 3 mm, and the sensor system had excellent static and dynamic characteristics.
Design of digital detection system for optical fiber sensor

Deng Wenhua,Zhang Hua,Li Yulong

DOI: https://doi.org/10.3969/j.issn.1002-7300.2010.12.020

2010-01-01

Abstract:To achieve stable detection of weak light-intensity in optical fiber sensor,This paper presents a design method of new digital fiber-optic sensor detection system based on the photoelectric sensor chip OPT211 and STC89C52RC single chip microcomputer.Detection system is composed by constant current drive circuit,light receiving device,signal conditioning circuit,AD Acquisition and display circuit.This design meet the requirements of optical fiber sensor technology.The system has achieved the 0~5 V voltage range,1 mV resolution and precision of 1‰ on sensor detection.With anti-interference ability,good stability,good linearity and high resolution characteristics.
Study of Fiber Grating Displacement Sensor

王冬生,王桂梅,潘玮炜,张凯

DOI: https://doi.org/10.3969/j.issn.1002-1841.2008.09.003

2008-01-01

Abstract:On the basis of analyzing and researching the principle of demodulation technique for FBG,a scheme of demodulation technique for FBG,which was based on cantilever tuning and the demodulation technique on a pair of matched FBG was designed.The relation between the wavelength shifts of sensing FBG and the wavelength shifts of reference FBG were studied,and each part of the system was designed.Stepping motor transformed the electricity pulse signal into angle-displacement or line-displacement's open-loop control part,in the non-overload situation,the electrical machinery rotational speed and the stopping position was only decided by the pulse signal's frequency and the pulse number,and was not influenced by the variation of load.This system has the characteristic of simply structure,high precision and low cost.
A simple and high-resolution POF displacement sensor based on face-coupling method

Abdul Ghaffar,Qi Li,Shah Ali Haider,An Sun,Arnaldo G. Leal-Junior,Lifeng Xu,Muhammad Chhattal,Mujahid Mehdi

DOI: https://doi.org/10.1016/j.measurement.2021.110285

IF: 5.6

2022-01-01

Measurement

Abstract:A Various fiber-optics displacement sensor methods are presented yearly, and a high-resolution displacement sensor with cost-effective and straightforward operation is an essential demand. Here, we present a novel sensor structure for displacement measurement. The design is based on a hole in the one fiber's core, whereas a second fiber is utilized to move inside the hole made on the first fiber. The optical power coupling varies with the distance between the first and second fiber. The drilling length is investigated, and the four sensors are fabricated with different displacement ranges. The results show drilling length influences sensor's range, and the sensor has a nanometer resolution of about 8.647 nm with a sensitivity of 11.56 nW/µm in between 0 µm and 2500 µm. Moreover, a maximum range of 4 mm is achieved. The designed structure could be used not only for displacement, but also for vibration, angle, and pressure sensor.

engineering, multidisciplinary,instruments & instrumentation
Experimental analysis of fiber-optic displacement sensors

Xuejin Li,Zhehuang Zhang,Yunjin Yu,Qinsong Lin

DOI: https://doi.org/10.1117/12.440225

2001-01-01

Abstract:The analysis of fiber-optic displacement sensors (FOS) was performed. A system comprising of two type of FOS was established to improve linearity, by making computation between a random type and a semicircle type reflective FOS. It was found, on the basis of measurement that the displacement sensor had a good linearity in a large range of more than 5mm.
Optimizing Algorithm for Existing Fiber-Optic Displacement Sensor Performance

Zeina Elrawashdeh,Christine Prelle,Frédéric Lamarque,Philippe Revel,Stéphane Galland

DOI: https://doi.org/10.3390/s24020448

IF: 3.9

2024-01-12

Sensors

Abstract:This paper describes the optimal design of a miniature fiber-optic linear displacement sensor. It is characterized by its ability to measure displacements along a millimetric range with sub-micrometric resolution. The sensor consists of a triangular reflective grating and two fiber-optic probes. The measurement principle of the sensor is presented. The design of the sensor's triangular grating has been geometrically optimized by considering the step angle of the grating to enhance the sensor's resolution. The optimization method revealed a global optimum at which the highest resolution is obtained.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Optical Fiber Displacement Sensing System Based on Dual-Wavelength with Single-Wavelength Interferometry

刘义秦,谢芳,马森,李昭莹

DOI: https://doi.org/10.16136/j.joel.2012.07.033

2012-01-01

Abstract:An optical fiber displacement sensing system with large distance and high precision, which combines dual-wavelength interferometry with single-wavelength interferometry, is presented. Based on the wavelength-division -multiplexing technology and employing fiber Bragg grating as in-fiber reflective mirror, the signal of dual-wavelength interferometry is seperated from the signal of single-wavelength interferometry,when two signals with different wavelength are applied on the interferometry simultaneously. The amplitude of the measured displacement is determined by the dual-wavelength interferometry and the maximum measurement step can be expanded to the order of millimeter. Under the two selected wavelengths of 1557.32 nm and 1558.52 nm,the maximum measurement is 0.5 mm. The displacement is measured by the signal of the single-wavelength interferometry, and the measurement precision is very high.
Fiber-optic Measurement System Used for Complex Surface Contour Digitizing （ⅰ）：research on the Key Technologies

ZHAO Yong,HU Tao,LI Peng-sheng,PU Zhao-bang

DOI: https://doi.org/10.3321/j.issn:1005-0086.2001.05.020

2001-01-01

Abstract:The fiber-optic sensor system used fo r complex surfacecontour measurement was discussed in this paper.Some key proble ms appeared when using fiber-optic sensor for displacement measurement were fairly settled .Experimental results approved the validity of the designed system,and the resul ts also indicated that the stability of the light power of LD was better than 0. 07 %,the lateral resolution was 8 μm and the measurement range was enlarged to 6 mm.
Multi-point Fiber Optic Displacement Sensing System Based on Cavity Length Detection

Fang Wang,Xiaozhi Qin,Xinyi Zhao,Qiulin Yuan,Yunqi Liu,Yongguang Huang,Xu Wang,Yufang Liu

DOI: https://doi.org/10.1109/jlt.2024.3481428

IF: 4.7

2024-01-01

Journal of Lightwave Technology

Abstract:We propose a macroscopic loss-based olive-shaped single-mode fiber (OSSMF) for displacement sensing in the fiber loop ring-down, which validates the feasibility of displacement sensing. In this work, two systems consisting of single-point and multi-point displacement sensing are built, and the ring-down curves are demodulated using low-cost microcontroller unit and self-developed optical time domain reflectometer (OTDR), respectively. The long-cavity system is initially utilized for single-point displacement sensing to confirm the possibility of multi-point displacement detection with short cavities. The relationship between cavity length and sampling frequency is also discussed, enabling low-frequency, high-precision sampling of the ring-down curve. In the short-cavity multi-point experimental system, different sizes of olive-shaped sensing heads are compared in a 65 m cavity length scenario. It is concluded that the OSSMF with a short axis of 2.1 cm and a long axis of 3.5 cm exhibited the highest sensitivity. The attenuation is -2.11 dB/ (km mm) in the 8-12 mm range and -7.24 dB/ (km mm) in the 12-24 mm range. The displacements are detected in 65 and 125 m fiber loop ring-down (FLRD) cavities, and the ring-down curves are processed using Fast Fourier Transform, this method addresses the issue in multi-point measurements where an extension cord is needed for time-domain differentiation. Different cavity length designs enable distributed measurements of physical quantities, the system is of great significance in the fields of structural engineering monitoring and geological disaster monitoring.
Embedded Design on Optical Coherence Tomography Control System

Wang Zhiguang,Wang Xiaoping,Zhong Genliang

DOI: https://doi.org/10.1117/12.783533

2009-01-01

Abstract:This thesis analyzes the principle of single-mode fiber OCT system and its control signal. Then it puts forward a design thought which it integrates various signals into the embedded OCT control system. These signals include galvanometer driving signals for rapid scanning optical delay line (RSOD), high-frequency sawtooth signals for Phase Modulator, control signals for electronic control displacement platform and amplifying and filtering circuit of scanning signals. Then we design and construct an embedded OCT integrated control system which uses ARM9 processor S3C2410A as the core. The system is integrated with many wave generating circuits, driving circuit for electric control displacement platform and amplifying& filtering circuit of feedback signals. The system discards the separated OCT system structure which is made up of many general instruments and has a high cost. The result is satisfactory. Besides, we introduce embedded Linux operating system into the system. As a result, the whole system has such features as low development and production cost, excellent extensibility and strong real time control function. Experimental results show that various control signals generated by our system meet the design demand and can be applied to practical OCT system.
An ultracompact high-resolution displacement sensor based on self-interference effect of single optical nanograting

Jie Qi,Chenguang Xin

DOI: https://doi.org/10.1117/12.2600368

2021-01-01

Abstract:Benefitting from properties including high sensitivity, high resolution, immunity to electromagnetic interference and remote sensing ability, optical-grating-based displacement measuring technologies have been widely used in many fields such as semiconductor manufacturing, precision machining, microscopic techniques and photolithography recently. In this work, high-resolution displacement measuring is demonstrated with an ultracompact structure consist of only a few optical components by using self-interference effect of a single nanograting. The resolution is demonstrated to be as low as 0.1-nm level. This method shows great potential in developing miniaturized high-resolution displacement devices and systems, which are highly demanded for future integrated high-precision machinery manufacturing systems.
Front-end Design of High Precision Displacement Sensor Based on Linear Array CCD

Ping Liao,Cheng Ren,Xiaoyu Yang

DOI: https://doi.org/10.3969/j.issn.1003-501x.2017.05.004

2017-01-01

Abstract:In order to achieve the high-precision non-contact measurement for tiny displacement, a high-precision displacement sensor front-end module is designed based on linear array CCD. An optical lens is designed using the principle of laser triangulation, and the system uses the FPGA to generate the drive timing required for the linear array CCD. The one-dimensional video signal output by CCD is handled to obtain a stable analog signal through the front circuit, and the signal is available for digital circuitry. The system has the characteristics of simple structure,small volume, stable output signal, high resolution and high precision. Experimental tests show that the sensor front-end module outputs are stable with small interference analog signal after calculation, the maximum range is ±15 mm, and the accuracy can reach 20 μm. The system can be widely used in the precise measurement of tiny displacement.
High-precision displacement measuring instrument based on PSoC3

CHEN Peng-jie,LU ling-xia,LI Hua-ming

DOI: https://doi.org/10.3969/j.issn.1001-4551.2012.09.010

2012-01-01

Abstract:In order to reduce production costs and the volume of high-precision displacement measuring instrument based on the the linear variable differential transformer(LVDT),and to make the products more competitive,taking the advantage that the PSoC3 is more system monolithic than traditional single-chip,a new design for displacement measurement system was proposed based on CY8C3866AXI by analyzing its working principles.The displacement of high-precision measurements was achieved through the use of PSoC3 within the digital module(DMA and LCD),the analog modules(AD,DA,PGA,etc.),and the signal modulation circuit was designed by oneself which is consisted of the rectifier circuit,filter circuit,and the subtraction circuit.The combination of ARM and AD698 product in the past was replaced by this design which has accuracy of 0.2 μm.The results indicate that this program has advantages such as high integration,good linearity and a low disbursement.
Displacement measurement system based on phase-sensitive detection and position sensitive detector

Pei HUANG,Bo CHEN,Yan LI

DOI: https://doi.org/10.7510/jgjs.issn.1001-3806.2017.02.018

2017-01-01

Abstract:In order to realize the measurement of micro displacement, a displacement detection system based on semiconductor laser with single mode optical fiber output and 2-D position sensitive detector(PSD) was developed to suppress ambient light noise effectively.The output power of laser was sinusoidally changed when injection current was modulated with 1kHz.The desired signals from PSD which is illuminated by the modulated light source are demodulated from the noise with phase-sensitive detection technique.In the signal processing circuit, using phase sensitive detection technology, the output alternating current signal of detector was demodulated and spot energy center position was gotten.Therefore, the disturbance of background light was eliminated.The results show that the measuring accuracy is better than 1μm.The study is helpful for multi-degree-of-freedom errors measurement.

Design of displacement measuring system using optical fibre sensor

Multimode-interference-effect-based all-fiber displacement sensing system for an orthopedic Ilizarov apparatus device.

Research of a Reflective Fiber-Optic Displacement Sensor with Intensity Compensation

A High-Resolution Displacement Sensor Based on a Grating Interferometer with the Phase Modulation Technique

Design and Operation of a Transmissive Plastic Fiber Optical Displacement Sensor

A Novel Optical Fiber Displacement Measurement System

Development of Wide Range Displacement Sensors Based on Polarized Light Detecting Technology

Design of a Reflective Intensity Optical Fibre Bundle Displacement Sensor

Design of digital detection system for optical fiber sensor

Study of Fiber Grating Displacement Sensor

A simple and high-resolution POF displacement sensor based on face-coupling method

Experimental analysis of fiber-optic displacement sensors

Optimizing Algorithm for Existing Fiber-Optic Displacement Sensor Performance

Optical Fiber Displacement Sensing System Based on Dual-Wavelength with Single-Wavelength Interferometry

Fiber-optic Measurement System Used for Complex Surface Contour Digitizing （ⅰ）：research on the Key Technologies

Multi-point Fiber Optic Displacement Sensing System Based on Cavity Length Detection

Embedded Design on Optical Coherence Tomography Control System

An ultracompact high-resolution displacement sensor based on self-interference effect of single optical nanograting

Front-end Design of High Precision Displacement Sensor Based on Linear Array CCD

High-precision displacement measuring instrument based on PSoC3

Displacement measurement system based on phase-sensitive detection and position sensitive detector