Abstract:Pure Titanium (Titanium grade 2) and Ti6Al4V (Titanium grade 5) alloys are commonly used biocompatible materials for medical bone implants and dental protheses. As some implants have to be removed after a certain amount of time after the implantation, the osteo repellent surface is one of the most important property for the removable bone implants such as bone screws and plates. On contrary, for the dental protheses the property of the most importance is osseointegration. Femtosecond laser treatment causes ablation and produces LIPSS ("laser induced periodic surface structures") which can consist of cones on macro scale and ripples on nano scale which showed structures and roughness similar to that of a bone. Therefore, surface modifications by electrochemical anodization and femtosecond laser could be seen as promising methods for improving both osteo-repellence and osteointegration properties of the bone implants and dental protheses. The aim of this work is electrochemical and surface characterization of the anodized Titanium and Ti6Al4V alloy treated by the femtosecond laser. Firstly, Titanium and Ti6Al4V samples were anodized potentiostaticaly up to 100V in 25% phosphoric acid solution for 120s. Following the potentiostatic anodization, samples were structured with femtosecond laser to produce micro cones and nano ripples on top of the cones. As a final step, laser treated spots were potentiodynamicaly anodized using a SDCM (Scanning Droplet Cell Microscopy) setup. Influence of different potentials, scan rates and electrolytes were studied and optimized, consequently. Morphology and topography were examined by the means of SEM (Scanning Electron Microscopy) and AFM (Atomic Force Microscopy), while crystallography was determined by the XRD (X-Ray Diffraction). Furthermore, the composition of the oxide layer was determined by the XPS (X-ray photoelectron spectroscopy). Oxide forming factor (k ox ), a relative permittivity ε r , and ECSA (Electrochemical surface area) were obtained from the cyclic voltammograms (CV) and electrochemical impedance spectroscopy (EIS) experimental data. Electrochemical impedance spectroscopy data was modeled and compared between not preanodized, preanodized and anodized and not anodized after femtosecond laser structuring. Finally, bioassessment with osteoblast was done to examine the growth of the osteoblast cells on the modified surface structures. Value of the oxide forming factor (k ox ) for the pure Titanium and Titanium grade 5 were successfully calculated and compared with a Scanning Electron Microscopy. Calculated values of the relative permittivity ε r are in agreement with the literature values. Finally, obtained results indicate that anodized and subsequently femtosecond laser treated samples could be used as medical bone and dental implants.

Preparation of Porous Microstructures on NiTi Alloy Surface with Femtosecond Laser Pulses

Biocompatibility of the micro-patterned NiTi surface produced by femtosecond laser

Formation, evolution and characterization of nanoporous structures on the Ti6Al4V surface induced by nanosecond pulse laser irradiation

Biocompatibility of micro/nano structures on the surface of Ti6Al4V and Ti-based bulk metallic glasses induced by femtosecond laser

Study on surface properties of nanosecond laser textured plasma nitrided titanium alloy

Effect of femtosecond laser processing atmosphere on micro-nano structures and wetting properties of Ti6Al4V surface

Preparation of Microstructure Laser Ablation and Multiple Acid-Etching Composites on the Surfaces of Medical Titanium Alloy TC4 by Laser Ablation and Multiple Acid-Etching, and Study of Frictional Properties of the Processed Surfaces

Cutting NiTi with Femtosecond Laser

Corrosion Behavior of NiTi Alloys Fabricate by Selective Laser Melting Subjected to Femtosecond Laser Shock Peening

Influence of femtosecond laser pulse sequence on the morphology and roughness of titanium surface micro-patterns

Light Nurtures Plants: The Picosecond Laser-induced Lithops-like Microstructures on Titanium Alloy Surface with Broad-band Ultra-low Reflectivity

Impact of Femtosecond Laser Treatment Accompanied with Anodization of Titanium Alloy on Fibroblast Cell Growth

Effect of microstructure and chemical composition on cell orientation and proliferation viability of titanium alloy processed by pulse lasers

Femtosecond Laser-Induced Evolution of Surface Micro-Structure in Depth Direction of Nickel-Based Alloy

Micro-and nano-structures on metal induced by femtosecond laser radiation

Microstructure and Hardness of the Laser Surface Treated Titanium

Picosecond laser texturing on titanium alloy for biomedical implants in cell proliferation and vascularization

Electrochemical Surface Characterization of a Femtosecond Laser Treated and Anodized Ti and Ti6Al4V Alloy for Bone and Dental Implants

In Vitro Bioactivity and Biocompatibility of Bio-Inspired Ti-6Al-4V Alloy Surfaces Modified by Combined Laser Micro/Nano Structuring

A Femtosecond Bessel Laser For Preparing A Nontoxic Slippery Liquid-Infused Porous Surface (Slips) For Improving The Hemocompatibility Of Niti Alloys

Ultrafast Laser Processing of Nanostructured Patterns for the Control of Cell Adhesion and Migration on Titanium Alloy