Abstract:Squeeze casting process can effectively resolve the casting difficulties for wrought aluminum alloys by pressurized solidification. The effects of applied pressure (0.1-125 MPa) on the microstructure refinement, non-equilibrium eutectic phase aggregation and fracture behavior of Al-Zn-Mg-Cu alloys prepared by squeeze casting were investigated through metallography, scanning electron microscopy and energy dispersive spectroscopy. The results showed that the primary α-Al grains transformed from coarse dendrites to refined equiaxed grains with increasing pressure. Considerable primary refinement was achieved at 100 MPa, with a significant decrease by 63% in the average grain size from 273 μm to 101 μm; the non-equilibrium eutectic phases were homogenized and refined, and almost dissolved into the Al matrix after T6 heat treatment. The mechanism of solidification behaviors in pressurized solidification was elucidated. Firstly, the applied pressure increased the thermodynamic driving force to promote primary grain nucleation. Secondly, the solute diffusion and constitutional undercooling at the front of the solid/liquid interface front were inhibited by pressure, and grain growth in a dendritic structure was thus restrained. Thirdly, interdependence theory and thermodynamic calculations were conducted to quantitatively describe the primary grain size changes under pressurized solidification. Lastly, the ternary eutectic reaction L → α-Al + T-Mg (Al, Zn, Cu) 2 + Al 2 Cu and binary eutectic reaction L→ α-Al + Al 7 Cu 2 Fe were suppressed by the reduced solute segregation. Furthermore, when the pressure increased from 0.1 MPa to 125 MPa, the ultimate tensile strength was raised from 428 MPa to 538 MPa, almost approaching that of samples by forging process. The refined eutectic phases decreased stress concentration and improved fracture behaviors.

Microstructure and Tensile Properties of Al-Cu-Si Alloy with Different Solidification Pressures

The effect of Si addition on the microstructure and tensile properties of casting Al-5.0Cu-0.6Mn-1.2Fe alloys

Microstructure, Mechanical Property and Thermal Conductivity of Al–Si–Fe–Mg Alloy Solidified under High Pressures

The Effect of Solution Treatment on the Si Particles’ Morphology Evolution and the Thermal Conductivity and Tensile Properties of Sb-Modified Al-8Si-0.6Mg Alloys

Microstructural Evolution and Mechanical Properties of Al–Si–Cu–(Ge)–(Mg) Alloy Solidified under High Pressure

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Microstructural evolution and precipitation behavior of Al-7Si-3Cu alloy prepared under 5 GPa

Effect of pressure on the microstructure refinement, solidification mechanism and fracture behavior of wrought Al-Zn-Mg-Cu alloys prepared by squeeze casting

Enhanced tensile properties in a high-pressure synthesized Al-Si-Cu-Ge-Mg alloy with nano-sized Al particles in eutectic Si

Correlation of Solidification Microstructure Refining Scale, Mg Composition and Heat Treatment Conditions with Mechanical Properties in Al-7Si-Mg Cast Aluminum Alloys

Effects of different holding pressures on the microstructure and mechanical properties of Al-5.9Zn-2.2Mg-1.8Cu alloy

Microstructure and Mechanical Properties of Cast Al-Li-Mg Alloy: Role of Cu Addition and Heat Treatment

Microstructure and Mechanical Properties of Cast Al-Si-Cu-Mg-Ni-Cr Alloys: Effects of Time and Temperature on Two-Stage Solution Treatment and Ageing

Influence of Thermal Rate Treatment and Low Temperature Pouring on Microstructure and Tensile Properties of AlSi7Mg Alloy

Effect of heat treatment on microstructure and tensile properties of 319 aluminum alloy

Effect of the Solid Solution and Aging Treatment on the Mechanical Properties and Microstructure of a Novel Al-Mg-Si Alloy

Nano-scale Reinforcements and Properties of Al-Si-Cu Alloy Processed by High-Pressure Torsion

Effect of Aging Treatment on Properties of Al–Si Alloy Solidified at High-Pressure

Enhancing Mechanical Performances by Unconventional Si Precipitates Obtained in Pressure-Induced Al-Si-Cu-(Mg) Solid Solutions

Effect of Cu addition on microstructures and tensile properties of high-pressure die-casting Al-5.5Mg-0.7Mn alloy

Detailed investigation on microstructure and strengthening contribution of Al- x Cu-1.3Li-X alloy sheets