Abstract:Abstract ITO was prepared by mixing gradient In 2 O 3 and SnO 2 powders using solid phase reaction manner. Using electron beam gun tool, ITO films with varied thicknesses were fabricated. The structure, electrical and optical parameters of the prepared films were studied. XRD patterns were used to establish the micro-structural parameters (lattice strain and crystallite size). The SEM shows improvement of grain size with the increase of the film thickness. The electrical parameters of ITO films were measured by means of the standard four-point probe method. It was found that when the film thickness increases from 75 nm to 375 nm, the resistivity decreases to lower value of 1.65×10 -4 Ω.cm and slightly increases to 1.93 ×10 -4 Ω.cm at thickness of 375 nm. The ITO films with lower electrical properties are appropriate for high-efficiency CdTe solar cells. In terms of spectral ellipsomeric, three optical layer models (adhesive layer of the substrate/B-spline layer of ITO film/surface roughness layer) were applied to estimate the film thickness with high accuracy. The absorption coefficient and energy gap were calculated from the transmission and reflection spectra in the strong absorption region. As the film thickness increases, the optical energy gap was found to increase from 3.56 eV to 3.69 eV. In terms of Hall-effect measurements, both carrier concentration and hall mobility were determined. In addition, influences of ITO layers with various thicknesses on the performance of CdS/CdTe solar cells were checked. When the ITO window layer thickness is 325 nm, J sc = 17 mA/cm 2 , V oc = 0.82 V, and FF = 57.4%, the calculated highest power conversion efficiency (PCE) is 8.6%.

Polycrystalline Cds/Cdte Thin-Film Solar Cells with Intrinsic Sno2 Films of High Resistance

High-efficiency CdTe-based Thin-Film Solar Cells with Unltrathin CdS:O Window Layer and Processes with Post Annealing

The Influence of CdS Intermediate Layer on CdSe/CdS Co-Sensitized Free-Standing TiO2 Nanotube Solar Cells

CdTe thin film solar cells with a SnTe buffer layer in back contact

The study on saturation current and ideality factor of CdTe solar cell based on CdS window layer deposited with hydrogen peroxide

High Efficiency CdTe Solar Cells with a Through-Thickness Polycrystalline CdTe Thin Film

Strategy for Performance Enhancement of Cd1-XZnXTe/CdS Core/shell Quantum Dot Sensitized Solar Cells Through Band Adjustment

Low-cost Fabrication of Cu 2 ZnSnS 4 Thin Films for Solar Cell Absorber Layers

An Optimized Multilayer Structure of CdS Layer for CdTe Solar Cells Application

Impact of high resistivity transparent (HRT) layer in cadmium telluride solar cells from numerical simulation

Performance Improvement of Solution-Processed CdS/CdTe Solar Cells with a Thin Compact TiO2 Buffer Layer

Effects of High Temperature Annealing on Sputtered Zn(O,S) Films for CdTe Solar Cells

A Study of Back Contacts of Cdte Thin Film. Solar Cells

Structure, Electrical and Optical Properties of ITO Thin Films and Their influence on Performance of CdS/CdTe Thin-Film Solar Cells

Solution-Processed Efficient Nanocrystal Solar Cells Based On Cdte And Cds Nanocrystals

Suppression of pinhole defects in thin film CdS/CdTe solar cell via gelatin-based negative photoresist passivation

Electrical Properties Of N-Type Cds And P-Type Cdte Thin Films In Cds/Cdte Solar Cells

Ultrathin chromium oxide buffer layer by reactive thermal deposition for high-performance semitransparent perovskite solar cells

Evaluation of AA-CVD deposited phase pure polymorphs of SnS for thin films solar cells

Solution-processed Efficient CdTe Nanocrystal/cbd-Cds Hetero-Junction Solar Cells with ZnO Interlayer

Highly-Crystalline SnO2 Thin Films for Efficient Planar Perovskite Solar Cells