Abstract:PURPOSE:To evaluate the effect of surface treatment on bonding strength between pure titanium formed by selective laser melting and porcelain.METHODS:Pure titanium strips (64) and cobalt-chromium alloy strips (16) were laser machined to meet ISO 9693 standards. The pure titanium specimens were divided into 4 groups according to the sandblasting pressure and interlayer material. The sandblasting pressure of 0.25 MPa of bonder porcelain group was TB1, the sandblasting pressure of 0.25 MPa of gold coating group was TG1, the sandblasting pressure of 0.45 MPa of bonder porcelain group was TB2, and the sandblasting pressure of 0.45 MPa of the gold coating group was TG2(n=16). After porcelain fusing, half of the specimens in each group were tested for three-point bend bonding strength, and the other half were tested after 10 000 cycles of thermal cycling(n=8). The bonding strength of cobalt-chromium alloy after sandblasting at 0.25 MPa and 0.45 MPa was taken as the control group and recorded as group C1, C2(n=8). The bonding strength was tested using classical three-point bending experiment. The surface roughness of pure titanium was measured by laser scanning confocal microscope(LSCM). Field emission scanning electron microscopy(FE-SEM) was used to observe the interface morphology of titanium-ceramic. The surface morphology of titanium after porcelain stripping was observed with stereomicroscope and fracture modes were analyzed by it. Graphpad Prism 8.0 software package was used for statistical analysis of the data.RESULTS:The bonding strength of group TG2 was (40.16±3.97) MPa and (37.38±2.39) MPa of group TG1, which were significantly higher than that of group TB2 (36.32±1.44) MPa and group TB1 (33.75±2.31) MPa (P＜0.05). The bonding strength of group TB2 with 0.45 MPa sandblasting was significantly higher than that of group TB1 with 0.25 MPa sandblasting (P＜0.05). There was no significant decrease in titanium-ceramic bonding strength before and after thermal cycling. When the sandblasting pressure increased from 0.25 MPa to 0.45 MPa, the roughness increased significantly (P＜0.05). The fracture modes were mixed.CONCLUSIONS:Under the conditions of this study, gold coating can significantly improve the bonding strength of Ti22 porcelain and SLM pure titanium than bonder porcelain, and increase of sandblasting pressure can further improve the bonding strength of titanium-porcelain. After 10 000 cycles of thermal cycling, the titanium-porcelain bonding strength did not decrease significantly.

Research of Adhesive Fatigue Strength Between Casting Pure Titanium and Different Resin Cements

Shear Bond Strength of Three Resin Cements to the Casting Pure Titanium

Effect of Selective Laser Melting Pure Titanium on Bond Strength of Titanium to Composite Resin by Different Surface Treatments

Effects of three stress levels on the fatigue properties and fracture mechanisms of an in-situ synthesized TiB/Ti-6Al-4V titanium matrix composite

Effect of sandblasting on the shear bond strength and durability of three resin cements bonded to titanium

Fatigue property and failure mechanism of TC4 titanium alloy in the HCF and VHCF region considering different forging processes

Microstructural effects on the high-cycle fatigue and fracture behaviors of Ti-6Al-4V alloy

Experimental Study on Forged TC4 Titanium Alloy Fatigue Properties under Three-Point Bending and Life Prediction

Cyclic fatigue of casting clasps in cobalt chromium alloy, titanium alloy and high cobalt chromium molybdenum alloy

Effect of Surface Treatment on the Three-Point Bend Bonding Strength Between Pure Titanium Fabricated by Selec-Tive Laser Melting and Porcelain

High cycle fatigue behavior of implant Ti-6Al-4V in air and simulated body fluid

Fatigue behavior of thin-walled grade 2 titanium samples processed by selective laser melting. Application to life prediction of porous titanium implants

Corrosion fatigue behavior of porous Cu-bearing Ti alloy fabricated by selective laser melting

Microstructure and pore sensitivities in very high cycle fatigue behaviors of titanium alloy welded joints under stress ratios

Defect-based fatigue crack nucleation and strength evaluation of additively manufactured TiC/Ti6Al4V titanium matrix composite at different temperatures

EVALUATION OF THE LONG-TERM DURABILITY OF HIGH-PERFORMANCE POLYIMIDE ADHESIVES FOR BONDING TITANIUM

Influence of Fine Grains on the Bending Fatigue Behavior of Two Implant Titanium Alloys

High cycle fatigue behavior of titanium microalloyed high-strength beam steels

Effect of TiN/Ti coating combined with laser shock peening pre-treatment on the fatigue strength of Ti-6Al-4V titanium alloy

Contact damage failure analyses of fretting wear behavior of the metal stem titanium alloy-bone cement interface

Understanding the Relations between Surface Stress State and Microstructure Feature for Enhancing the Fatigue Performance of TC6 Titanium Alloy