Abstract:The purpose of strengthened plasters (interior applications) and renders (exterior applications) in this paper is to control cracks at the interface between the main structure and the infill wall rather than strengthen masonry and reinforced concrete structures. Cracks in plasters and renders have caused severe issues that need to be resolved urgently. Cracks affect not only the aesthetics but also the normal use of a building. The presence of cracks changes the perceptions of the owners of a structure, forcing them to question its safety and even take legal action against its developer. Consequently, the present paper discusses the effects of different strengthening materials on the tensile behaviour of plasters and renders, particularly on the first cracking. One test group without strengthening materials and six test groups with strengthening materials were tested under uniaxial tensile loads. Each experimental group included the same six specimens. A glass fibre-reinforced polymer (GFRP) grid, two types of basalt fibre-reinforced polymer (BFRP) grids, and three types of welded wire meshes (WWMs) were selected as the strengthening materials in the tests. Four types of plasters and renders were used: cement mortar, anti-crack mortar, gypsum plaster, and thermal insulation mortar. The crack pattern, stain–stress relationship, first cracking strain, energy dissipation capacity in the uncracked stage, and microstructure were investigated to gain better insight into the tensile behaviour of the plasters and renders. It was found that a strengthening material with a small mesh size resulted in numerous cracks and a narrow crack spacing. The stress–strain curves of the strengthened specimens could be divided into uncracked and cracked stages. The higher slopes in both stages of the strengthened specimens could be attributed to the higher longitudinal strain coefficient, smaller opening size, and larger cross-sectional area of each strand of the strengthening materials. The first cracking strain of the unreinforced specimen was smaller than that of a strengthened specimen. Stronger bond strength between plaster/render and strengthening material, smaller mesh size and greater cross-sectional area of each strand of strengthening material led to the larger first cracking strain. The energy dissipation capacity in the uncracked stage of the strengthened thermal insulation mortar was the least. The energy dissipation capabilities in the uncracked stage of the plasters/renders reinforced with BFRP grid-2 and WWM-3 were the second-highest and highest, respectively. The bond strengths of the GFRP and BFRP grids to the plasters/renders were stronger than those of the WWMs. The bond strengths between the gypsum plaster and the reinforcing materials were the highest, whereas those between the thermal insulation mortar and the strengthening materials were the lowest. Additionally, stress–strain relationships were proposed for the strengthened plasters and renders; the results were found to be in good agreement with the test results.

Fabrication and application of a new type of plasters

The Performance Characteristics of Sand Wall-like Architectural Coatings and Construction Technology for Imitation Exterior Wall Brick

Effect of waterproof agent on performance of inorganic lightweight aggregate thermal insulating mortar

Effect of Different Strengthening Materials on Tensile Behaviour of Plasters and Renders

Development and application of inorganic-organic compound thermal insulating mortar

Development of Imitation Marble Architectural Coating

Preparation and Experimental Study on A New Type of Exterior Wall Putty

MODIFICATION ANALYSIS AND EXPERIMENTAL STUDY OF MOSONRY MORTAR

Moisture buffer, fire resistance and insulation potential of novel bio-clay plaster

A New Method on Laboratory Evaluation of the Effectiveness of Consolidant Treatments for the Conservation of Historic Stone Buildings and Sculptures

Polymer Modification Technology of Expanded Perlite and Polymer Thermal Insulation Mortar

A comprehensive performance evaluation of the cement-based expanded perlite plastering mortar

Development of Clay-Composite Plasters Integrating Industrial Waste

Comparison of consolidation effectiveness of acrylic non-aqueous dispersion and other anti-weathering conslidants for earthen architecture and monuments [Original title and text in Chinese]

Evaluation of Technological Properties of Mortars with the Addition of Plaster Byproduct

Effect of multiphasic structure of binder particles on the mechanical properties of a gypsum-based material

Experimental Study with Plaster Mortars Made with Recycled Aggregate and Thermal Insulation Residues for Application in Building

Development and application of novel microfine cement-based grout

Semi-real-time infrared thermography for detecting layering defects in plasters solidification within indoor environments

Mechanical Properties of Composite Mortar for Residential Drick Walls

Effect of Portland Cement on the Selected Properties of Flue Gas Desulfurization Gypsum-Based Plasters