Abstract:AISI 52100 steel has been widely used in the mechanical industry due to its excellent mechanical properties and high availability. In some cases, an ultra-smooth surface of AISI 52100 steel is needed and is even indispensable for the satisfactory performance of devices. In this paper, chemical mechanical polishing technique was employed to prepare the ultra-smooth surface of AISI 52100 steel. Colloidal silica was used as the abrasive. The effects of pH, complexing agent such as glycine, H2O2 and benzotriazole (BTA) on the polishing performance were studied. It is revealed that, with the increase of pH, the static etching rate (SER) and the material removal rate (MRR) are both gradually reduced, and the post-CMP surface roughness I?, decreases. This is attributed to the fact that compact and passive iron oxides, especially Fe(III) oxides, gradually form on the top surface. At pH 4.00, in the presence of glycine, and with the increase of the H2O2 concentration, the SER is further suppressed, and the surface roughness R-a gradually decreases; the MRR initially dramatically increases due to the fact that, with the addition of small amount of H2O2, the porous iron oxide layer with relatively low mechanical strength can be rapidly formed on the surface. Moreover, glycine intensifies the chemical dissolution by chelating iron ions, especially Fe(II) ions, and thereby the mechanical strength of the oxide layer further weakens. Then, after reaching the peak value, the MRR gradually decreases when the H2O2 concentration further increases since the compactness of the oxide layer gradually increases. With the increase of the BTA concentration, the MRR is gradually suppressed and the surface roughness R-a decreases due to the formation of Fe-BTA passivating film on the top surface. Finally, a two-step polishing process was developed. The polishing results show that, within 20 min, a rough surface of AISI 52100 steel with the R-a value of 188 nm can be polished into an ultra-smooth surface with the R-a value of 1.8 nm. (C) 2015 Elsevier B.V. All rights reserved.

Preparation of Superfine Polishing Wax for Stainless Steel

Preparation of a high-efficient ultrasonic wax remover used at low temperature for stainless steel polishing

Preparation of superamphiphobic stainless steel surface by laser and perfluorooctanoic acid treatment

Preparation and Self-Cleaning Properties of a Superhydrophobic Composite Coating on a Stainless Steel Substrate

Analysis for Components of a Polishing Wax

Preparation of super-hydrophobic surface on stainless steel

Study on Dry-Ice Particle Jet Polishing Process of 316L Stainless Steel Electrode

Chemical Mechanical Polishing of Steel Substrate Using Colloidal Silica-Based Slurries

Preparation Technology of Water Based Detergent for Q235 Carbon Steel

Preparation of Stainless Steel Superhydrophobic Surface and Analysis of Hydrophobic Mechanism

Chemical Mechanical Polishing of Stainless Steel As Solar Cell Substrate

Effects of pH Values and H2O2 Concentrations on the Chemical Enhanced Shear Dilatancy Polishing of Tungsten

Achieving a super-smooth surface of stainless bearing steel with chemical mechanical polishing via controlling corrosive wear of Fe and Cr

Fabrication of superhydrophobic stainless steel via hybrid femtosecond laser-chemical method with wear-resistance and anti-corrosion properties

Formation mechanism of superhydrophobicity of stainless steel by laser-assisted decomposition of stearic acid and its corrosion resistance

A comprehensive study on electrochemical polishing of tungsten

Effect of Ingredients in Slurry Containing Alumina on Polishing of Hard Disk Substrate

Series Lectures on Metallic Chemical Polishing Technic PartⅠ-Chemical Polishing on Steel Parts

Mechanical, chemical and wetting properties of a superhydrophobic surface based on functionalized ZrO2 on stainless steel

Theoretical and Experimental Study of Ultrasonic Vibration-Assisted Laser Polishing 304 Stainless Steel

Design and preparation of ZnS superhydrophobic coating with self-healing property and oil-water separation function on stainless steel mesh surface