Abstract:Ni-based single crystal line alloy is constituted with gamma phase and gamma' phase in the form of coherency. Since an indenter for two-phase coherent structure is bigger than the usual nano-scale indenter, the press location of indenter may be unclear in nanoindentation simulation. Both gamma phase and gamma' phase may be pressed initially, and the mechanical properties shown are different because of the initial press locations. The nanoindentation of Ni-based single crystal line alloys is simulated by molecular dynamics method. Two models are used to study about the hardness in [001] crystal orientation, one is the model gamma/gamma' with the initial indentation on gamma phase, and the other is the model gamma'/gamma with the initial indentation on gamma' phase. The influence of misfit dislocation at (001) interface on nanoindentation of the two models is analyzed using a center-symmetry parameter. Results show that the misfit dislocation shape of the two models are different after relaxation. Lomer-Cottrell dislocation occurs on (001) interface in the gamma'/gamma model. Before 0.930 nm press depth is reached, there is little change in the (001) interface misfit dislocation of the two models. Relationship between press load and press depth is similar for the two models, and it is the same in the relationship between hardness and press depth. After press depth reaches 0.930 nm, the misfit dislocation at (001) interface for model gamma'/gamma grows big, which results in a smaller press load and a smaller hardness computation in the model gamma'/gamma than that in model gamma/gamma'. When the press depth reach 2.055 nm, we find only a small amount of dislocations in gamma phase that can go into gamma' phase since the misfit dislocation at (001) interface in model gamma/gamma' hinders the process. However, none of dislocations can go into gamma phase because of the prevention caused by Lomer-Cottrell dislocation at the (001) interface in the model gamma'/gamma. That means the Lomer-Cottrell dislocation reinforces the material obviously. So the press load in model gamma'/gamma grows faster than that in model gamma/gamma'.

Analysis of the nanoindentation load–displacement curves measured on high-purity fine-grained alumina

Influence Of Initial Indentation Point On Nanoindentation Of Ni-Based Single Crystal Line Alloys

Effect of peak load on the determination of hardness and Young's modulus of hot-pressed Si3N4 by nanoindentation

Influnence of Indenter on the Nanoindentation of Ni Based Single Crystal Alloy

Influence of Friction in Material Characterization in Microindentation Measurement.

Investigation on Dynamic Hardness and High Strain Rate Indentation Size Effects in Aluminium (110) Using Nano-Impact

Analysis of the Nanoindentation Data Measured with a Berkovich Indenter for Brittle Materials: Effect of the Residual Contact Stress

Anisotropic Elastic Recovery Behavior of AlN Ceramic During Nanoindentation and Scratching

Description of the Nanoindentation Unloading Curves with a Universal Function: Theoretical Consideration and Applications to Brittle Materials

Comparison of nano-indentation hardness to microhardness

On the description of indentation size effect in hardness testing for ceramics: Analysis of the nanoindentation data

QUASICONTINUUM ANALYSIS OF INDENTER SIZE EFFECT IN NANOINDENTATION TESTS

Instrumented Microindentation of Nanoporous Alumina Films

Analysis of Load-Displacement Curves of Ceramics Measured with Low-Load Vickers Hardness Test: Indentation Size Effect

Micromechanical characterization of zirconia and silicon nitride ceramics using indentation and scratch methods

Nanoindentation Characterization of the Hardness of Zirconia Dental Ceramics

Factors Influencing Nanoindentation Test Data

Experimental and Simulation Analysis of Residual Topography Dominated Deformation Mechanism of Nanoindentation: a Case Study of Inconel 625 Superalloy

Modeling Effect of Surface Roughness on Nanoindentation Tests

Nanoindentation Characterization of SiC-based Ceramics

Determination of the Load-Independent Hardness by Analyzing the Peak-Load-Dependence of the Unloading Slope in Nanoindentation